TREE

Low Voltage Cut-Out Circuit diagram. This circuit will detect when the voltage of a 12v battery reaches a low level. This is to prevent deep-discharge or maybe to prevent a vehicle battery becoming discharged  to a point where it will not start a vehicle. This circuit is different to anything previously presented. It has HYSTERESIS. Hysteresis is a feature where the upper and lower detection-points are separated by a gap.  Low Voltage Cut-Out Circuit diagram :   Low Voltage Cut-Out Circuit Diagram Normally,  the circuit will deactivate the relay when the voltage is 10v and when the load is removed. The battery voltage will rise slightly by as little as 50mV and turn the circuit ON again. This is called "Hunting." The off/on timing has been reduced by adding the 100u. But to prevent this totally from occurring, a 10R to 47R is placed in the emitter lead. The circuit will turn off at 10v but will not turn back on until 10.6v when a 33R is in the emitter. The value o...

Description . This circuit can be used to test whether mains voltage is present or not without having electric contact with mains line. The CMOS IC CD4033 is the heart of this circuit. The CD4033 consists of a 5 stage decade Johnson counter and an output decoder for converting the Johnson code to a 7 segment decoded output for driving 7 segment LED display . A 10cm long insulated copper wire connected to the clock pin (pin1) of the IC serves as the sensor. The sensor wire has to be placed in the vicinity of the mains wire to be tested. When there is no voltage in the mains line, no voltage will be induced in the sensor wire and the display will show a random digit. When there is voltage in the mains line, a small voltage will be induced in the sensor wire due to electromagnetic induction and this voltage is sufficient enough to clock the CMOS IC CD4033. Now the display will count from zero to nine and repeat. Circuit diagram. Notes. The circuit can be assembled on a Vero board. U...

In this post I will share about using Accu source to charge batteries that can be used on any mobile brand, or can be called universal phone battery charger. Because the battery charger using a source of 12V, the charge accumulator can also be used in cars and others. This will out charger circuit voltage of 5 volts DC, with input from at least 6 volt battery, and voltage inputs that have been tried till with 15 volts (more than it has not been tried, because the battery that tie the maximum output voltage is only 13.8 volts).

This is the Simple Over Voltage Protector Circuit Diagram. The whole circuit of over voltage protector is build and fabricated around operational amplifier used as comparator. The inverting input is given to pin 2 of op-amp IC (IC1) with reference voltage of 5.1V from zener diode. Similarly, non-inverting input is given to pin no 3 of IC1 use as sensor for over voltage protector for sensing voltage fluctuation in the mains. The two transistors T1 and T2 conduct alternating (i.e. one at a time) according to the voltage of mains. Simple Over Voltage Protector Circuit Diagram When voltage is around or below 240V AC transistor T1 is in off-state where T2 energized relay RL1. Similarly, when voltage becomes beyond 240V (i.e. above 240V) T1 is in conducting-stage and T2 is in off-stage which de-energized the relay RL1 and switch-off the appliance. PARTS LIST Resistors (all ¼-watt, ~+mn~ 5% Carbon) R1 = 147 Ω/2W R2 = 100 Ω/1W R3 = 330 Ω R4 = 100 KΩ R5 = 1.8 KΩ R6, R7 = 1 KΩ VR1 = 10 KΩ VR2 = ...

All miniature electronic devices operate off batteries. Some of them need higher than the standard battery voltages to operate efficiently. If the battery of that specific voltage is unavailable, we are forced to connect additional cells in series to step up the DC voltage. Thus, the true meaning of miniaturisation is lost. A simple way to overcome this problem is to employ a voltage doubler, if the device under consideration can operate at a small current. Here we present a low-power voltage doubler circuit that can be readily used with devices that demand higher voltage than that of a standard battery but low operating current to work with. The circuit is quite simple as it uses only a few components. Yet, the output efficiency is 75 to 85 percent along its operating voltage range. The available battery voltage is almost doubled at the output of the circuit. Here IC1 is wired as an astable multivibrator to generate rectangular pulses at around 10 kHz. This frequency and duty cycle of...

This circuit, designed on request, has proven to be useful to indicate when the voltage in a power supply line is changing from 120V to 240Vac. It can be used in different circumstances and circuits, mainly when an increase in ac or dc supply voltage needs to be detected. D3 illuminates when the line voltage is approaching 120V and will remain in the on state also at 240V supply. On the other hand, D6 will illuminate only when the line voltage is about 240V and will stay on because the latching action of Q1, Q2 and related components. C1, D1 and D2 provide a low dc voltage in the 4.5V - 6V range in order to allow proper operation of latch circuit and LEDs. Circuit diagram   Parts: R1_____________470R 1/2W Resistor R2_____________220K 1/4W Resistor R3,R7__________470R 1/4W Resistors R4_______________1K 1/4W Resistor R5_______________2K2 1/4W Resistor R6_____________330R 1/4W Resistor C1_____________330nF 630V Polyester Capacitor C2______________10µF 25V Electrolytic Capacitor D1,D2_...

This is a very simple circuit which can be modified to the user's needs. Its operation is simple, when the input voltage is 0, the LED (LO). The LED turns off when the voltage increases to the level determined by R2. Voltage Monitor Circuit Diagram

This circuit indicates which of three voltages in the range from about about -4V to about +4V - at A, B and C - is the highest by lighting one of three indicator LEDs. Alternatively, it can be wired to indicate the lowest of three voltages or to indicate both the highest and lowest voltages. Op amps IC1a, IC1b & IC1c are wired as comparators, while the three indicator LEDs and their series 1kO current limiting resistors are strung across the op amp outputs to implement the appropriate logic functions.  Maximum Minimum Voltage Indicator Circuit Diagram For example, LED A will light only when pin 8 of IC1c is low (ie, A greater B) and pin 7 of IC1b is high (ie, A greater C). Similarly, LED B will light only when pin 8 of IC1c is high (ie, B greater A) and pin 1 of IC1a is low (ie, B greater C). LED C works in similar fashion if the voltage at C is the highest. Note that if all the LEDs and their parallel 1N4148 diodes are reversed, the circuit will indicate the lowest of the thr...

AMPLIFIER Stereo mode 80 W + 80 W (4 Ω at 1 KHz, THD 10 %) Surround mode 80 W + 80 W (4 Ω at 1 KHz, THD 10 %) FRONT SPEAKER Model CMS4320F Type 2 Way 2 Speaker Impedance 4 Ω Rated Input Power 80 W Max. Input power 160 W SMPS SCHEMATIC MAIN AMPLIFIER MAIN DSP SERVO FRONT CIRCUIT MICOM VOLTAGES AUDIO PROGRAM Download program file name must be CM4320_***.HEX If security program (Water Wall) is activated on your PC, you must save the file to the USB storage device and disable the security software, then download the file to your set. Caution: When downloading the file, you should neither unplug the USB device, change to the other function, nor power off the device. USB device must be unplugged when the downloading process is completed. CD PROGRAM Download program file name must be HE001_DATE_00.BIN If security program (Water Wall) is activated on your PC, you must save the file to the USB storage device and disable the security software, then download the file to your set. Caution: When do...

This is a simple project Using IC NE 555 Voltage Inverter Circuit Diagram.In many circuits we need to generate an internal adjustable voltage. This circuit shows how it is possible to use a trusty old NE555 timer IC and a bit of external circuitry to create a voltage inverter and doubler. The input voltage to be doubled is fed in at connector K1. To generate the stepped-up output at connector K2 the timer IC drives a two-stage inverting charge pump circuit. The NE555 is configured as an astable multivibrator and produces a rectangular wave at its output, with variable mark-space ratio and variable frequency. This results in timing capacitor C3 (see circuit diagram) being alternately charged and discharged; the voltage at pin 2 (THR) of the NE555 swings between one-third of the supply voltage and two-thirds of the supply voltage. Voltage Inverter Circuit Using IC NE555  The output of the NE555 is connected to two voltage inverters. The first inverter comprises C1, C2, D1 and D2. The...

The circuits were designed using a single IC L200 to create two different regulators where one circuit functions as high current regulator using NPN pass transistors while the other circuit functions as programmable voltage and current regulator. Terminology L200 – a monolithic integrated circuit for voltage and current programmable regulation, available in Pentawatt package or 4-lead TO-3 metal case, used to replace fixed voltage regulators when high output voltage precision is required and eliminates the need to stock a range of fixed voltage regulators due to it features of low standby current drain, low bias current on regulation pin, thermal overload protection, output transistor SOA protection, short circuit protection, input overvoltage protection, adjustable output voltage and current, and blow-out proof because of current limiting and power limiting LM741 – a general purpose single operational amplifier with features such as offset null, compensated internal frequency, volta...

Build a simple Capacitance to Voltage Meter Circuit Diagram . In this volt meter circuit uses timer Ul operates as a free-running oscillator at 60 Hz, providing trigger pulses to timer U2 which operates in the monostable mode. Resistor Rl is fixed and capacitor Cx is the capacitor being measured.   Capacitance to Voltage Meter Circuit Diagram While the output of U2 is 60 Hz, the duty cycle depends on the value of Cx. U3 is a combination low-pass filter and unity-gain follower whose dc voltage output is the time-averaged amplitude of the output pulses of U2, as shown in the timing diagram. The diagram shows when the value of Cx is small the duty cycle is relatively low. The output pulses are narrow and produce a lower average dc voltage level at the output of U3.  As the capacitance value of Cx increases, the duty cycle increases making the output pulses at U2 wider and the average dc level output at U3 increases. The graph illustrates capacitance values of 0.01 ?¥ to 0.1 ...

Fluorescent lamp assembly using only a 3V voltage source. 2 battery which i parallel to supply its circuit of fluorescent lamp . By using the above circuit is very useful if it saves electricity and power outages at home , or used in  a dark place. Circuit of works, and lamp lights This is circuit , battery , and fluorescent lamp 20W Working circuit on the dark

This circuit allows a 240V mains appliance to be controlled remotely via low-voltage cabling and a pushbutton switch. The mains appliance (in this case, a light bulb) is switched with a suitably-rated relay . All of the electronics is housed in an ABS box located in proximity to the appliance. The pushbutton switch and plugpack are located remotely and can be wired up with 3-core alarm cable or similar. Cable lengths of 20m or more are feasible with this arrangement. When the switch (S1) is pressed, the input (pin 8) of IC1c is briefly pulled low via the 10mF capacitor, which is initially discharged. Low-Voltage Remote Mains Switch Circuit diagram: Low-Voltage Remote Mains Switch Circuit Diagram The output (pin 10) immediately goes high and this is inverted and fed back to the second input (pin 9) via another gate in the quad NAND package (IC1d). In conjunction with the 1MW resistor and 470nF capacitor, IC1d eliminates the effects of contact "bounce" by ensuring that IC1c’s o...

The hobby circuit below uses an unusual method to generate about 12,000 volts with about 5uA of current. Two SCRs form two pulse generator circuits. The two SCRs discharge a 0.047uF a 400v capacitor through a xenon lamp trigger coil at 120 times a second. 12KV High Voltage Generator Circuit Diagram The high voltage pulses produced at the secondary of the trigger coil are rectified using two 6KV damper diodes. The voltage doubler circuit at the secondary of the trigger coil charges up two high voltage disc capacitors up to about 12KV. Although this circuit can’t produce a lot of current be very careful with it. A 12KV spark can jump about 0.75 of an inch so the electronic circuit needs to be carefully wired with lots of space between components. Source by : Streampowers

The car cigarette lighter socket does not only light cigarettes, but can be utilized as an electrical channel for powering tools to work on the car such as laptops and other electronic devices. The following circuit diagram shows a way of powering a two-way mobile radio using the LM317 T voltage regulator . The LM317 T is an adjustable 3-terminal positive voltage regulator that efficiently provides a load current of 1.5 Amps over an output range of 1.2 V and 37 V. With reference to the circuit, it can accept 14 volts without any hassle and the voltage can be controlled easily with the use of a potentiometer, a 3-terminal resister with sliding contact. The whole circuit will contain the following components:  Printed Circuit Board (PCB) Resistor 1 (R1): 270 ohms Resistor 2 (R2): 2K carbon potentiometer Capacitor 1 (C1): 100nF Capacitor 2 (C2): 1uF tantalum LM317T Voltage Regulator Heat Sink DC Power Jacks Green LED: Power Red LED: Over Voltage Zener Diode: over voltage LED switch Th...

With a suitable load, the terminal voltage of a NiCd or lithium-ion battery is proportional to the amount of stored energy. This relationship, which is linear over a wide range, can be used to build a simple battery capacity meter. Circuit Image :   Voltage Tester for Model Batteries Circuit Image  This model battery tester has two functions: it provides a load for the battery, and at the same time it measures the terminal voltage. In addition, both functions can be switched on or off via a model remote-control receiver, to avoid draining the battery when it is not necessary to make a measurement. The load network, which consists of a BC517 Darlington transistor (T2) and load resistor R11 (15 Ω /5 W), is readily evident. When the load is active, the base of T1 lies practically at ground level. Consequently, T1 conducts and allows one of the LEDs to be illuminated. Circuit Diagram : Voltage Tester for Model Batteries Circuit Diagram The thoroughly familiar voltmeter circuit, whi...

The BVM1 is an ultra low power ten LED battery voltmeter circuit that is optimized for monitoring solar-charged 12V battery systems. The circuit features an expanded meter scale that displays ten color-coded voltage steps from 10.5V to 15.0V. Power is conserved by only turning on the appropriate LED for a short but bright flash once every 1.25 seconds. The LED display can be turned on continuously (no blinking) by turning the Calibrate switch on, more battery power is consumed in this mode. BVM1-12 Volt Battery Voltage Monitor With Parts List  The BVM1 also includes a battery low voltage beeper that warns when the battery voltage drops below a preset voltage. The beeper can be turned on and off with the L.V. Beep Activate switch. The BVM1 is protected against reverse voltage connection and is fused for safety. The design goals of this circuit were efficiency, simplicity, reliability and the use of field replaceable parts. The BVM1 circuit has been designed to work in conjunction w...

This circuit is used to monitor the battery voltage to display a dual-colored LED status of the battery to. If the LED “green”battery voltage exceeds 11.9 volts. If the yellow LED , battery voltage 11.9 to 11.5 volts. If the LED is “red” If the battery voltage below 11.5 volts. You can of course change the trigger points by the trimmer resistors and / or changing the value of the resistors in the divider.  .  Simple Car Battery Voltage Monitor Circuit Diagram . A dual op amp is used as a comparator. The green LED on the board, until the voltage exceeds 11.5 volts. The red LED illuminates when the voltage falls below 11.9 volts to the circuit. Therefore, in the 11.9 to 11.5 volts, both LEDs are on, producing a slightly yellow color. When the voltage falls below 11.5 V, the green LED , and now only the red LED flashes to indicate low voltage. Parts List R1=1K2 R2-3-4=680R R5=15K R6=10K R7-8-9-10=1K IC1=LM324 D1=5V6 /0.5W Zener D2-3-4-5=LED RV1=10K trimmer  Is recommend...

To obtain a pure DC voltage, then we must consider the regulation voltages and currents that we change from AC to DC current. For that we need some settings that can support our own making and its components were easy to get in the electronics market. This is series Power Supply that can be used on trafo 5 Ampere up to 10 Amperes. If you want to use a larger transformer than 5 Amperes transistor 2N3055 is suggested that the double for the exit of the collector current is larger and in accordance with the current out of the transformer. How pemasanganya enough in the series on all sides of the pin.