Skip to main content

Simple 110 and 220V AC LED Voltage Indicator


This circuit, designed on request, has proven to be useful to indicate when the voltage in a power supply line is changing from 120V to 240Vac. It can be used in different circumstances and circuits, mainly when an increase in ac or dc supply voltage needs to be detected. D3 illuminates when the line voltage is approaching 120V and will remain in the on state also at 240V supply. On the other hand, D6 will illuminate only when the line voltage is about 240V and will stay on because the latching action of Q1, Q2 and related components. C1, D1 and D2 provide a low dc voltage in the 4.5V - 6V range in order to allow proper operation of latch circuit and LEDs.

Circuit diagram

 

Parts:

  • R1_____________470R 1/2W Resistor
  • R2_____________220K 1/4W Resistor
  • R3,R7__________470R 1/4W Resistors
  • R4_______________1K 1/4W Resistor
  • R5_______________2K2 1/4W Resistor
  • R6_____________330R 1/4W Resistor
  • C1_____________330nF 630V Polyester Capacitor
  • C2______________10µF 25V Electrolytic Capacitor
  • D1,D2________1N4007 1000V 1A Diode
  • D3,D6___________LEDs (Color and shape at will)
  • D4_________BZX79C10 10V 500mW Zener Diode (See Notes)
  • D5___________1N4148 75V 150mA Diode
  • Q1____________BC547 45V 100mA NPN Transistor
  • Q2____________BC557 45V 100mA PNP Transistor

Notes:

  • D4 value could require some adjustment in order to allow precise switching of the circuit at the chosen voltage. If the case, please try values in the 8.2V - 15V range.
  • Warning! The circuit is connected to 240Vac mains, then some parts in the circuit board are subjected to lethal potential! Avoid touching the circuit when plugged and enclose it in a plastic box.

Labels:

Comments

Post a Comment

Popular posts from this blog

A basic Arduino Solar PV Monitor

I have just recently had solar pv installed, mainly to future proof my energy costs, I do not expect it to be like drilling for oil in my back garden, however the return looks to be encouraging. The install gives you another single unit meter, from this you will see the total amount the panels produce, but that is about it. I wanted to know how much the production was as it was happening, I discovered the light blinks on the front of the meter will flash 1000 times for each kWh of electricity which passes through. The rate of the flashing of the LED tells you how much power is currently passing through the meter. [ ]
Post a Comment
Read more

Apple releases TV spot for new iPods

Apple has just released a fun commercial to showcase its new line of iPod players and the various colours they come in. The TV spot titled ‘Bounce’, has a bunch of colourful iPod touch, iPod nano and iPod shuffles er…bouncing to music. With all that colour and dancing and bouncing, you may forget that Apple’s latest gen line of iPods has some other awesome features. For instance, the fifth gen iPod touch comes with Siri, 4-inch retina display and an A5 chipset. Maybe the next ad will showcase some of these features with less bouncing.link
Post a Comment
Read more

3 Channels Audio Splitter Amplifier Circuit Diagram using TL084

This is the schematic diagram of 3 channels audio splitter amplifier circuit which built using op-amp IC TL084. The 3 channels amplifier output distribution applies a single TL084.   3 Channels Audio Splitter Amplifier Circuit Diagram The very first step is to capacitive coupling having a p. 1.0 ~ electrolytic capacitor. The entries are railways Vee Y2 or 4.5 V. This enables working with an individual 9V power source. A voltage gain of 10 (1 M?/100 Kohm) is obtained in the first stage, as well as the other three floors are connected as a unity gain voltage followers. Every single output stage drives independently through an amplifier output 50 pF capacitor towards the resistance of 5.1 k ohm load. The response range is flat from 10 Hz to 30 kHz.
2 comments
Read more