TREE

How to Build a 3000W Stereo Power Amplifier Circuit Diagram? Lets start first we define 3000wstereo power amplifier circuit diagram this circuit has a power output of up to 1500W RMS power amplifier circuit is often used to power sound systems spelunker for outdor. In the final image can be seen a series of power amplifiers using 10 sets of power transistors for the ending. This power amplifier circuit using a transistor amplifier from the front, signal splitter, driver and power amplifier. Current consumption required is quite large power amplifier that is 15-20 A 1500W power amplifier circuits for this. Supply voltage needed by the power of this amplifier is the optimal working order symmetrical 130VDC (130VDC-130VDC ground). 1500W amplifier circuit below is a picture series of mono, stereo if you want to make it necessary to make two copies of the circuit. For more details can be viewed directly image the following 1500W power amplifier circuit. The series of High Power Amplifier 15...

Usually, Low-Cost Stereo Level Indicator home stereo power amplifiers don’t have output level indicators . An output power level indicator can be added to each channel of these stereo power amplifiers . As low levels of the output power are not disturbing and damaging to the people, there is no need to add a preamplifier and low-level detector before IC LM3915. But you should know when the output power becomes considerably high. Here we present a very simple, low-cost stereo-level indicator circuit for home power amplifiers with power rating of around 0.5W. The circuit is built around two LM3915 dot/bar display driver ICs (IC1 and IC2). LM3915 senses analogue voltage levels to drive ten LEDs, providing a logarithmic 3dB/step analogue display. Stereo Level Indicator Circuit Diagram The voltage levels below 1V are not important because these correspond to a low level of the audio signal. Similarly, input voltage levels above 30V correspond to too high levels of the output power, which ...

Circuit diagram for Stereo 20 W BTL power amplifier AN7190 Datasheet for AN7190: Download

This is a one watt home stereo amplifier module project using the KA2209 IC from Samsung, which is equivalent to the TDA2822. It operates from 3-12V DC & will work from a battery since the dormant current drain is low. It requires no heat sink for normal use. The input & output are both ground referenced. Maximum output will be obtained with a 12V power supply & 8 ohm speaker, however it is suitable for driving headphones from a supply as low as 3V. The Specifications of the home stereo amplifier : D.C. input : 3 – 12 V at 200 – 500 mA max Idle current : approx. 10 mA Power output : > 1 Watt max. 4-8 ohms, 12V DC Freq. Resp. : approx. 40 Hz to 200 kHz, 8 ohm, G=10 THD : < 1 % @ 750 mW, 4-8 ohm, 12V Gain : approx. x10 (20 dB) OR x100 (40dB) S/N ratio : > 80 dB, G = 20 dB Sensitivity : < 300 mV, G = 20 dB Input Impedance : approx. 10 k ohm Description   The gain is adjustable from ten to 100, i.e. twenty to 40 dB. Start with feedback resistors R1 and R3 of 1k...

This stereo balance indicator circuit diagram is designed using few common external components .The schematic circuit is very simple to build and will provide an visual indication with LEDs for left , right and center balance .  Stereo Balance Indicator Circuit Diagram Outputs from each channel are fed to the two inputs of IC1 connected as a differential amplifier . Output of the IC1 is connected to the noninverting inputs of the IC2 and IC3 . If the outputs of the IC1 approaches the supply rail , the outputs of the IC2 and IC3 will go high illuminating the LED 3 , this will show that the right channel is dominating . If the sound is balanced to the left channel , the Ic2 and IC3 will go low and the LED1 will light . If both channels are equal in amplitude the outputs of the IC2 and IC3 would be low and high respectively , lighting up LED2 .

This is a schematic of a 10W stereo audio amplifier using TDA2009A amplifier IC. TDA2009A is a good IC provides quality sound. It has built in features like output current protection and thermal protection etc. The circuit can be operate between 8 to 24V DC with 1 to 2 amphere. 10W Stereo Audio Amplifier Circuit Diagram : If you want to operate this 10 watt amplifier circuit with watt amplifier circuit with mains supply then use a filtered and stable power supply to reduce mains hum. 10 watt out put power can be obtained by providing 20V 1.5A to the circuit. Use good and thick heatsink with the IC.

I am planning on doing an s-video and rca jack mod on my Genesis. The mods I see done seem to all use the headphone jack as the source of the stereo sound. Is this the only way? I would prefer to have the output not be controlled by the volume slider. Is it possible to tap the signals before they go to the amp and route them to my own (fixed-gain) amp? Any help/advice is much appreciated.. visit page.  Line Level Stereo Output on Genesis

2×160 W at 10% THD+N Into 8-Ω BTL  2×210 W at 10% THD+N Into 6-Ω BTL  1×300 W at 10% THD+N Into 4-Ω PBTL 2 x 210 Watt STEREO DIGITAL AMPLIFIER POWER STAGE

This is a schematic of a 10W stereo audio amplifier using TDA2009A amplifier IC. TDA2009A is a good IC provides quality sound. It has built in features like output current protection and thermal protection etc. The circuit can be operate between 8 to 24V DC with 1 to 2 amphere. 10W Stereo Audio Amplifier Circuit Diagram : If you want to operate this 10 watt amplifier circuit with watt amplifier circuit with mains supply then use a filtered and stable power supply to reduce mains hum. 10 watt out put power can be obtained by providing 20V 1.5A to the circuit. Use good and thick heatsink with the IC.  Source By : Circuitsstream

Ql is an audio amplifier and Ul is used as a 31.5-kHz subcarrier, which is similar to 38-kHz FM MPX.  Pilot frequency is 15.734 kHz.   Stereo Tv Decoder Circuit

General Description: The TDA7265SA is class AB Dual Audio Power amplifier assembled in the @ Clipwatt 11 package, specially designed for high quality sound application as Hi-Fi music centers and stereo TV sets. The TDA7265SA is pin to pin compatible with TDA7269, TDA7269A, TDA7269SA, TDA7265,TDA7499, TDA7499SA.  Circiut Diagram: 18W+18W Stereo Amplifier

Amplifiers which run from 12V DC generally don`t put out much power and they are usually not hifi as well. But this little stereo amplifier ticks the power and low distortion boxes. With a 14. 4V supply, it will deliver 20 watts per channel into 4-ohm loads at clipping while harmonic distortion at lower power levels is typically less than 0. 03%.  visit page. via next.gr High-Performance 12V 20W Stereo Amplifier

LM4910 belonging to the Boomer series of National Semiconductors is an integrated stereo amplifier primarily intended for stereo headphone applications. The IC can be operated from 3.3V ans its can deliver 0.35mW output power into a 32 ohm load. The LM4910 has very low distortion ( less than 1%) and the shutdown current is less than 1uA. This low shut down current makes it suitable for battery operated applications. The IC is so designed that there is no need of the output coupling capacitors, half supply by-pass capacitors and bootstrap capacitors. Other features of the IC are turn ON/OFF click elimination, externally programmable gain etc. Circuit diagram of the LM4910 stereo headphone amplifier is shown above.C1 and C2 are the input DC decoupling capacitors for the left and right input channels. R1 and R2 are the respective input resistors. R3 is the feed back resistor for left channel while R4 is the feed back resistor for the right channel. C3 is the power supply filter capacitor...

This power amplifier can use IC TDA1510 or TDA1515, minimum voltage require 6 volt and maximum voltage require 18 Volt, Voltage with DC supply voltage.Power output  2x 30 Watt stereo amplifier , with 2 ohms impedance , its is low impedance . You can use the fullrange or woofer speakers. see schematic below :

BH1417 IC The circuit shown here is of a good Stereo FM transmitter that can transmit high quality signals up to a range of 70 feet. The circuit is based on BH1417 PLL stereo transmitter IC from Rhom semiconductors. The IC has separate audio processing sections for the left and right channels, pre emphasis circuit for improving signal to noise ratio, crystal control circuitry for accurate frequency locking, multiplex circuit for making sum ( left plus right) and difference ( left minus right) {see this article for better understanding – Stereo decoder circuit} etc. Another important feature of this IC is that the transmission frequency can be set using a 4 channel DIP switch. The IC can be powered from anything between 4 to 6V DC and has an output power around 20mW. At full output power the circuit consumes only 20mA and has a channel separation of 40dB.There are 14 possible preset transmission frequencies, starting from 88.7MHz and incrementing in steps of 0.2MHz that can be selected ...

This circuit operate with IC AN7156N . You just can use this IC , because hav'nt similarity it. In this Circuit have 2 input IN R and IN L and have Output R and L . Voltage supply require 15 V , minimum voltage 9 V and maximum voltage 24V . And the voltage must DC voltage , and better the DC voltage filtering . Maximum Output for 1 speaker 25 W , so this circuit have maximum output 2 X 25 W with minimum impedance 4 ohm. See this circuit schematic below : Click image to view enlarge

Using a mobile phone while driving is dangerous. It is also against the law. However, you can use your mobile phone as a powerful music player with the help of a stereo power amplifier. This does away with the need of a sophisticated in-dash car music system. Most mobile phones have a music player that offers a number of features including preset/manual sound equalisers. They have standard 3.5mm stereo sockets that allow music to be played through standard stereo headphones/sound amplifiers. Nokia 2700 classic is an example.  Circuit diagram : Mobile Car Stereo Player Circuit Diagram   A car audio amplifier with 3.5mm socket can be designed and simply connected to the mobile phone output via a shielded cable with suitable connectors/jacks (readymade 3.5mm male-to-male connector cable is a good alternative). Fig. 1 shows the circuit of car stereo player. It is built around popular single-chip audio power amplifier TDA1554Q (IC1). The TDA1554Q is an integrated class-B power amp...

This mini stereo power amplifier provides up to 75 W of power on every channel by 4 ohms. unite your inputs using the RCA jacks. Outputs ended standard spokeswoman get behind jacks. It’s compatible with a few audio or else laptop device - you can even hook up an iPod using a 3.5mm to RCA jack converter. Treble, low, and volume controls on the front accede to you twist your sound to exactly how you aim it. Runs on 110 otherwise 220 vs.. The PCA3 mini stereo power amplifier from Pyle provides up to 75W of power on each one channel by 4 Ohms. link up your inputs using the RCA jacks, and output an better audio intimate done standard amplifier momentum jacks. It’s compatible with several audio before workstation device--you can even hook up an iPod using a 3.5mm to RCA jack converter. A master volume control on the front lets you adjust the get, and treble, deep, and volume controls on the front give permission you pull your sound to exactly how you be looking for it. The PCA3 runs on 110V ...

This amplifier circuit or with it based on ic KA2210 main amplifier, audio amplifier circuit should disupplay minimum of 10 Volt and up to 16 volts. Power output is 2 x 5.5 W stereo amplifier att. By using this amplifier you can listen to the strains of songs from mp3 player, iPod, etc. This is schematic diagram Part List R1 = 4.7R R2 = 4.7R C1 = 1uF C2 = 100uF C3 = 47uF C4 = 100uF C5 = 0.1uF C6 = 1000uF C7 = 1uF C8 = 100uF C9 = 47uF C10 = 100uF C11 = 0.1uF C12 = 1000uF IC = KA2210