TREE

This is a simple Project of 12 V AC Dimmer Circuit Diagram. 12-V AC Dimmer Circuit Diagram The circuit described here is derived from a conventional design for a simple lamp dimmer, as you can see if you imagine a diac connected between points A and B. The difference between this circuit and a normal diac circuit is that a diac circuit won’t work at 12 V. This is the fault of the diac. Most diacs have a trigger voltage in the range of 30 to 40V, so they can’t work at 12 V, which means the dimmer also can’t work. 12-V AC Dimmer Circuit Diagram The portion of the circuit between points A and B acts like a diac with a trigger voltage of approximately 5.5 V. The network formed by R1, P1 and C1 generates a phase shift relative to the supply voltage. The ‘diac equivalent’ circuit outputs a phase-shifted trigger pulse to the triac on each positive and negative half-cycle of the sinusoidal AC voltage. This works as follows. First consider the positive half of the sine wave. C1 charges when the...

This is a very simple build Electronic Circuit Project of single solar cell trickle charges 3- to 16-v battery in-circuit.   Many battery-powered applications use very little power when idle and have short-duration operating periods. Thus, the total energy used is very small. It would be convenient to incorporate solar cells in these devices to charge the batteries. However, the number of cells needed to charge a given battery voltage is close to Vb/0.6, thereby necessitating an array of solar cells, series connected. Single Solar Cell Trickle Charges 3- To 16-V Battery in-Circuit: The circuit in the figure addresses that issue by employing a self-oscillating boost circuit operating from a single solar cell. As such, it's able to trickle charge the battery continuously. The solar cell charges C2 until there's sufficient voltage to activate Q2. This will cause the output of U1a to turn on and latch on through the action of U1b. U1a's output also turns on Q3, which begins tra...

The supply receives - 20 V from the rectifier/filter which is fed to the collector of the Darlington pnp pass transistor, a TIP105. The base drive to the TIP105 is supplied through resistor R5. The base of the TIP105 is driven from Vz terminal at pin 9, which is the anode of a 6.2-V zener diode that connects to the emitter of the uA723 output control transistor. Circuit diagram : 15-V 1-A Regulated Power Supply Circuit Diagram The method of providing the positive feedback required for foldback action is shown. This technique introduces positive feedback by increased current flow through resistors R1 and R2 under short-circuit conditions. This forward biases the base-emitter junction of the 2N2907 sensing transistor, which reduces base drive to the TIP105.

This is Christmas season so you all may get ready to do lots of variations for your house for your gardens.In Christmas Christmas tree gets an important place so I decided to give very important circuit to decorate your Christmas tree here these bulbs are blinking.Moving 1M preset the speed of the bulb can be changed.about 20 bulbs (25w) Can be connected for this circuit.  230 v Christmas Flash Light Circuit Diagram Note # All the resistors must be 1/4w. # When you work with 230 be careful always try to get the assistance of an elder.

 230 V AC To 400 V DC Power Supply Circuit Diagram:   Description : A lot of students are who don't know how to convert 230 volt AC to 400 DC. So today i am published  ' 230 V AC to 400 V DC circuit diagram ' on my blog. Working principle of this circuit diagram is very simple. You already knew the working principle of a bridge rectifier. This circuit is same as bridge rectifier and the working principle is also same. The fuse is used to protect the circuit, if the current is greater than 1 A. Parts List Component No: Value F1 1 A B1 IN4007  C1 470MF/450V  V1 230 V AC 

The supply receive from 220 /120/110 Volt AC , then lowered by the transformer . Then receives +20 Volts DC from rectifier / filter section. This applied to pin 11 and 12 of the IC uA723/LM723 , as well as to the collector of the 2N3055 series pass transistor. The output through R1 and R2, providing about 7 V with respect to ground at pin 4. The reference terminal at pin 6 is tied directly to pin 5 , the non inverting input of the error amplifier . For fine trimming the output voltage , a potentiometer can be installed between R1 and R2. A 100-pF capacitor from pin 13 to pin 4 furnishes gain compensation for the amplifier. Base drive to the 2N3055 pass transistor is furnishes by pin of the uA723. Since desired output of the supply is 1 Ampere, maximum current limit is set to 1,5 Ampere by resistor Rsc whose value is 0,422 Ohm. A 100uF electrolytic capacitor is used for ripple voltage reduction at the output. A 1 kOhm output resistor provides stability for the power supply under no - lo...