Skip to main content

Posts

Showing posts with the label 12V

Universal battery charger with 12V source voltage

In this post I will share about using Accu source to charge batteries that can be used on any mobile brand, or can be called universal phone battery charger. Because the battery charger using a source of 12V, the charge accumulator can also be used in cars and others. This will out charger circuit voltage of 5 volts DC, with input from at least 6 volt battery, and voltage inputs that have been tried till with 15 volts (more than it has not been tried, because the battery that tie the maximum output voltage is only 13.8 volts).

500W Mos Fet Power Inverter from 12V to 110V 220V

 500W Mos-Fet Power Inverter from 12V to 110V/220V This circuit will provide a very stable "Square Wave" Output Voltage. Frequency of operation is determined by a pot and is normally set to 60 Hz. Various "off the shelf" transformers can be used. Or Custom wind your own FOR BEST RESULTS. Additional MosFets can be paralleled for higher power. It is recommended to Have a "Fuse" in the Power Line and to always have a "Load connected", while power is being applied. The Fuse should be rated at 32 volts and should be approximately 10 Amps per 100 watts of output. The Power leads must be heavy enough wire to handle this High Current Draw!

6V to 12V Converter Circuit Diagram

This inverter circuit can provide up to 800mA of 12V power from a 6V supply. For example, you could run 12V car accessories in a 6V (British?) car. The circuit is simple, about 75% efficient and quite useful. By changing just a few components, you can also modify it for different voltages. Notes L1 is a custom inductor wound with about 80 turns of 0.5mm magnet wire around a toroidal core with a 40mm outside diameter. Different values of D3 can be used to get different output voltages from about 0.6V to around 30V. Note that at higher voltages the circuit might not perform as well and may not produce as much current. You may also need to use a larger C3 for higher voltages and/or higher currents. You can use a larger value for C3 to provide better filtering. The circuit will require about 2A from the 6V supply to provide the full 800mA at 12V. 6V to 12V Converter Circuit Diagram   Parts R1, R4 2 2.2K 1/4W Resistor R2, R3 2 4.7K 1/4W Resistor R5 1 1K 1/4W Resistor R6 1 1.5...

12V battery indicator level

The following sequence is useful to show the battery voltage (battery) 12 volts. Voltage level is shown with four lights led. To facilitate the reading of the led is arranged in a vertical array. Led top three chosen by the green LED while the lowest is selected the color red. If the battery voltage continues to decline (because of usage), the Led-Led will turn off sequentially from the top to the bottom. Until if battery voltage is below 11.83 volts then only the red LED that lights up which means that the charge batteries are empty. Even this red Led will die if the stress continues to drop to below 11.5 volts. The working principle of this circuit is a comparison of battery voltage with a reference voltage. Schematic Battery level indicator

Simple 500W 12V to 220V Inverter

500W 12V to 220V Inverter Circuit Diagram   This is a 500W DC-to-AC inverter circuit diagram which produces an AC output at line frequency and voltage. 12VDC to 220V 50Hz inverter circuit will power 220V or 110V appliances from 12V car battery. The circuit is easy to make and is low cost. Use proper transformer. The output (in watts) is up to you by selecting different power rating transformer and power transistor rating. If you load electronic device which require 120V AC, then use transformer with 120V in output.

500W Cheap 12V to 220V inverter Circuit Diagram

Build a simple 500W Cheap 12V to 220V inverter Circuit Diagram.  In this circuit 4047 is use to generate the square wave of 50hz and amplify the current and then amplify the voltage by using the step transformer. 500W Cheap 12V to 220V inverter Circuit Diagram How to calculate transformer rating The basic formula is P=VI and between input output of the transformer we have Power input = Power output For example if we want a 220W output at 220V then we need 1A at the output. Then at the input we must have at least 18.3V at 12V because: 12V*18.3 = 220v*1 So you have to wind the step up transformer 12v to 220v but input winding must be capable to bear 20A.   Source: www.circuitsproject.com

TL594 12V DC Switch Mode Power Supply Circuit Diagram

Basic Of Switch Mode Power Supply In recent years, the use of switch mode power supply (SMPS) has become more comon as more applications demand for greater power eficiency. It makes use of semiconductor (mostly MOSFET) fast switches to switch DC input that has been rectified at high frequency. The advantages of high frequency switching are that it reduces the size of inductor, capacitors & transformer used. Other advantages of switching power supply over linear power supply are : 1) High Efficiency (up to 90% and above for nice design). 2) Output can be higher than input. 3) Able to operate over a variety of input power supply. 4) Able to have over output. The setback of using SMPS compared to linear power supply is that it generates electrical noise which contributes to electromagnetic compatibility design issues & more part count. Buck Converter SMPS The SMPS circuit below from Power Integration makes use of LNK304 as its high frequency switch. Take note that this circuit is...

6V to 12V Converter Circuit Diagram

This inverter circuit can provide up to 800mA of 12V power from a 6V supply. For example, you could run 12V car accessories in a 6V (British?) car. The circuit is simple, about 75% efficient and quite useful. By changing just a few components, you can also modify it for different voltages. Notes L1 is a custom inductor wound with about 80 turns of 0.5mm magnet wire around a toroidal core with a 40mm outside diameter. Different values of D3 can be used to get different output voltages from about 0.6V to around 30V. Note that at higher voltages the circuit might not perform as well and may not produce as much current. You may also need to use a larger C3 for higher voltages and/or higher currents. You can use a larger value for C3 to provide better filtering. The circuit will require about 2A from the 6V supply to provide the full 800mA at 12V. 6V to 12V Converter Circuit Diagram   Parts R1, R4 2 2.2K 1/4W Resistor R2, R3 2 4.7K 1/4W Resistor R5 1 1K 1/4W Resistor R6 1 1.5...

High Performance 12V 20W Stereo Amplifier

Amplifiers which run from 12V DC generally don`t put out much power and they are usually not hifi as well. But this little stereo amplifier ticks the power and low distortion boxes. With a 14. 4V supply, it will deliver 20 watts per channel into 4-ohm loads at clipping while harmonic distortion at lower power levels is typically less than 0. 03%.  visit page. via next.gr High-Performance 12V 20W Stereo Amplifier

Build a LT3582 12 DC 5V to 12V DC Converter

Using LT3582 -12 dual channel DC DC converter integrated circuit, manufactured by Linear Technology, can be designed a very simple step up dc converter. This 5 to 12V c converter electronic project provide both positive and negative outputs required in many biasing applications such as active matrix OLED (organic light-emitting diode)displays as well as CCD (charge coupled device) applications. The LT3582 offer an I2C interface that can dynamically program output voltages, power sequencing and output voltage ramps as the application requires. The LT3582’s positive output voltage can be set between 3.2V and 12.775 in 25mV steps, whereas the negative output can be set between -1.2V and -13.95V in 50mV steps. The LT3582-12 is preconfigured with ±12V output, requiring no future programming.

12V battery indicator level

The following sequence is useful to show the battery voltage (battery) 12 volts. Voltage level is shown with four lights led. To facilitate the reading of the led is arranged in a vertical array. Led top three chosen by the green LED while the lowest is selected the color red. If the battery voltage continues to decline (because of usage), the Led-Led will turn off sequentially from the top to the bottom. Until if battery voltage is below 11.83 volts then only the red LED that lights up which means that the charge batteries are empty. Even this red Led will die if the stress continues to drop to below 11.5 volts. The working principle of this circuit is a comparison of battery voltage with a reference voltage. Schematic Battery level indicator

12V To 24V DC DC Converter Circuit Diagram

This is a simple project of 12V To 24V DC-DC Converter Circuit Diagram .This simple 12V To 24V DC-DC Converter Circuit Diagram can provide up to 24V from a 12V source. It can be used to run radios, small lights, relays, horns and other 24V accessories from a 12V vehicle with a maximum draw of about 800mA.  It can be used to charge one 12V battery from another, or step up the voltage just enough to provide necessary overhead for a 12V linear regulator. Using one op-amp as a square wave oscillator to ring an inductor and another op-amp in a feedback loop, it won't drift around under varying loads, providing a stable 24V source for many applications. With a wide adjustment in output this circuit has many uses.  12V To 24V DC-DC Converter Circuit Diagram Parts Part Total Qty. Description Substitutions R1, R2, R3, R4, R8, R7 6 100K 1/4W Resistor R5 1 470 Ohm 1/2W Resistor R6 1 10K Linear Pot C1 1 0.01uF Mylar Capacitor C2 1 0.1uF Ceramic Disc Capacitor C3 1 470uF 63V Electrolytic C...

USB 5V to 12V DC DC Step Up Converter by LT1618

This is a 5V to 12V DC-DC step-up (boost) converter circuitry that is especially ideal for the USB powered applications. First of all a USB port has two current supply modes. Before detecting the connected device, it supplies maximum 100mA to the load. After recognizing the device, it increases the output current up to 500mA. In this circuit, controller (LT1618) also provides two input current modes. 100mA and 500mA input modes can be selected by the user. USB 5V to 12V DC-DC Step-Up Converter by LT1618  Output currents are limited due to the increased potential difference at the output. When the demand of the load increases, output voltage will start to decrease. For example, if the circuit operates in the 100 mA input mode, when the load is 35 mA, the output voltage will be kept at 12V. But if the load increases to 50 mA, output voltage will reduce to 8V to maintain the constant 100 mA input current.

Project of 12V Speed Controller Dimmer Circuit Diagram

This is a simple Project of 12V Speed Controller Dimmer Circuit Diagram. This handy circuit can be used as a speed controller for a 12V motor rated up to 5A (continuous) or as a dimmer for a 12V halogen or standard incandescent lamp rated up to 50W. It varies the power to the load (motor or lamp) using pulse width modulation (PWM) at a pulse frequency of around 220Hz.  SILICON CHIP has produced a number of DC speed controllers over the years, the most recent being our high-power 24V 40A design featured in the March & April 2008 issues. Another very popular design is our 12V/24V 20A design featured in the June 1997 issue and we have also featured a number of reversible 12V designs.   Project Image :  12V Speed Controller/Dimmer Project Image For many applications though, most of these designs are over-kill and a much simpler circuit will suffice. Which is why we are presenting this basic design which uses a 7555 timer IC, a Mosfet and not much else. Being a simple de...

How to build 1 5V to 5V 12V DC DC Converter with LT1073

Small 1.5V to 5V or 12V DC/DC converter with LT1073 chip. The IC is available in three different versions, depending on output voltage. Two with fixed output voltage of 5V and 12V, and the most interesting that can be adjusted. The adjustment is done through a voltage divider with two resistors, of mass, output and Terminal 8, internally connected to the voltage comparator IC, which is responsible for stabilizing the output voltage. LT1073 has an internal everything you need to make a small DC / DC converter with a low operating voltage of only 95μA 1V and consumption without load. If you do not have a meter inductance, the inductive part of the drive is a bit more complicated to make, but we shall see some possible solutions. Capacitor also recommended by the manufacturer for the circuit is a bit hard to get, I have used a tantalum recovered from another power source, and the ripple voltage at the output is quite low. Last but not least, say that the diode has to be a fast, not...

12V to 220V 100W Transistor Inverter Circuit Diagram

 12V to 220V 100W Transistor Inverter Circuit Diagram 12V to 220V 100W transistor based power inverter.

12V Fan Directly on 230V

This Electronic Circuit idea is certainly not new, but when it comes to making a trade-off between using a small, short-circuit proof transformer or a capacitive voltage divider (directly from 230 V mains voltage) as the power supply for a fan, it can come in very handy. If forced cooling is an afterthought and the available options are limited then perhaps there is no other  choice. At low currents a capacitive divider requires less space than a small,  short-circuit proof transformer.  12V Fan Directly on 230V Circuit Diagram: R1 and R2 are added to limit the inrush current into power supply capacitor C2 when switching on. Because the maximum rated operating voltage of resistors on hand is often not known, we choose to have two resistors for the current limit. The same is true for the discharge resistors R3 and R4  for C1. If the circuit is connected to a mains  plug then it is not allowed that a dangerous voltage remains on the plug, hence R3 and R4.  C...

Monitor for 6V 12V Batteries

Rechargeable batteries of 6V and 12V are used in a large number of applications. It is imperative that these are maintained properly to get maximum life out of them. Further, their permissible number of charge-discharge cycles must be fully utilised. Here is a circuit that gives a visual as well as an audible alarm if the battery voltage is higher or lower than acceptable limits, so that corrective action can be taken. Circuit and working As shown in Fig. 1, the circuit is built around dual-operational amplifier LM358 (IC1), hex inverting Schmitt trigger 74HC14 (IC2) and a few other components. The circuit can be divided into two parts—the input unit built around two operational amplifiers (op amps) in IC1 working as comparators, and audio alarm unit built around two RC oscillators and a transistor. Voltage from the battery under test (BUT) is applied to connector CON1. It is divided by five by R1 and R2 for comparison with the threshold levels. the power supply of the circuit is limit...