Skip to main content

Posts

Showing posts with the label Guitar

Vocal Adaptor for Bass Guitar Amp

These days, music is a major hobby for the young and not-so-young. Lots of people enjoy making music, and more and  more dream of showing off their talents on  stage. But one of the major problems often encountered is the cost of musical equipment. How many amateur music groups sing through an amp borrowed from a guitarist or bass player?  This is where the technical problems arise not in terms of the .25” (6.3 mm)  jack, but in terms of the sound quality (the words are barely understandable) and volume (the amp seems to produce fewer decibels than for a guitar). What’s more, unpredictable feedback may cause damage to the speakers and is very unpleasant on the ear. This cheap little easy-to-build project can help solve these technical problems. A guitar (or bass guitar) amplifier is designed first and foremost to reproduce the sound of the guitar or bass as faithfully as possible. The frequency response of the amp doesn’t need to be as wide or as flat as in hi-fi (p...

Guitar Effect Pedal Power

A small box is fitted to the rear of the amplifier providing a 9V output for the effect pedal. The amplifier section gets 9V through a pedal switch. This power output and guitar signal input lines are combined into a single unit with multi-way cable connecting points as shown in the following figure. Circuit diagram : Guitar Effect Pedal Power Circuit Diagram The circuit can be divided into two sections: power supply and signal handling. The power supply section is built around transformer X1, regulators 7805 and 7905, bridge rectifier comprising diodes D1 through D4, and a few discrete components. The signal-handling circuit is built around two OP27 op-amps (IC3 and IC4). The power supply of about 9V for the effect pedals is derived from step-down transformer X1. MOV1 is a metal-oxide varistor that absorbs any large spike in mains power.  IC 7905 (IC1) is a -5V low-power regulator. By using a 3.9V zener diode (ZD1) at its ground terminal, you get -8.9V output. The same technique ...

100W Guitar Amplifier

Guitar amplifiers are always an interesting challenge. The tone controls, gain and overload characteristics are very individual, and the ideal combination varies from one guitarist to the next, and from one guitar to the next. There is no amp that satisfies everyone's requirements, and this offering is not expected to be an exception. The preamp is now at Revision-A, and although the complete schematic of the new version is not shown below, the fundamental characteristics are not changed - it still has the same tone control "stack" and other controls, but now has a second opamp to reduce output impedance and improve gain characteristics. One major difference from any "store bought" amplifier is that if you build it yourself, you can modify things to suit your own needs. The ability to experiment is the key to this circuit, which is although presented in complete form, there is every expectation that builders will make modifications to suit themselves. The amp is...

Guitar Amp Circuit

Bass guitar super bridge amplifier 200 watt.  If you want to circuits amplifiers for bass guitar, or for using in every situation such as both listen to in the house, outside the house or outdoors. this. Guitar amp tone effects placement, Information about distortion voicing, effects placement, and cranked-tube-amp tone at any volume.. Amp parts | guitar center, Enjoy the lowest prices and best selection of amp parts at guitar center. most orders are eligible for free shipping!

Guitar Pedal Mods Modifications

Two Volume Knobs / Switchable Big Muff Tone Control Circuit Diode Clip Modification Dual Voltage Fuzz Boost Modification More Modifications Op Amp Pin Outs

Vocal Adaptor for Bass Guitar Amp

These days, music is a major hobby for the young and not-so-young. Lots of people  enjoy  making  music,  and  more  and  more dream of showing off their talents on stage. But one of the major problems often encountered is the cost of musical equipment. How many amateur music groups sing  through an amp borrowed from a guitarist or bass player? This is where the technical problems arise not in terms of the .25” (6.3 mm)  jack, but in terms of the sound quality (the words  are barely understandable) and volume (the amp  seems to produce fewer decibels than for a guitar). What’s more, unpredictable feedback may cause damage to the speakers and is very unpleasant on the ear. This cheap little  easy-to-build project can help solve these technical  problems. Vocal Adaptor for Bass Guitar Amp Circuit Diagram A guitar (or bass guitar) amplifier is designed first and foremost to reproduce the sound of the guitar or bass as faithf...

Mini Portable Guitar Ampls

This small amplifier was intended to be used in conjunction with an electric guitar to do some low power monitoring, mainly for practice, either via an incorporated small loudspeaker or headphones. The complete circuit, loudspeaker, batteries, input and output jacks can be encased in a small box having the dimensions of a packet of cigarettes, or it could be fitted also into a real packet of cigarettes like some ready-made units available on the market. This design can be used in three different ways: Mini Portable Guitar Amplifier Max output power:  1.5W @ 9V supply - 8 Ohm load; 60mW @ 3V supply - 8 Ohm load Frequency response:  Flat from 20Hz to 20kHz Total harmonic distortion @ 100mW output:  0.2% Max input voltage @ 3V supply:  8mV RMS Minimum input voltage for Fuzz-box operation:  18mV RMS @ 3V supply Current consumption @ 400mW and 9V supply:  200mA Current consumption @ 250mW and 9V supply:  150mA Current consumption @ 60mW and 3V supply: ...

Hofner Colorama II restoration project part 8 painting the guitar body

In the last blog post, we lacquered the neck on our vintage Hofner Colorama II guitar . Today we will paint the body. Before painting, we do a last check for anything we may have missed, like scrapes or gouges in the wood. This leads us to discover that the raw plug/screw anchor that someone had inserted to hold on the rear strap button, and which we were just going to leave, is, in fact, just half a raw plug. So, out it comes: A new hole is drilled: A wooden plug is cut: Glued in: And filed/sanded flat: Finally, we drill a new strap button hole: Et voilà. Also, since we're at it, let's drill a hole from the control cavity through to the tremolo area, so that we can earth (ground) the tremolo unit when we put this thing back together: Now on with the show. A quick mounting system needs to be fabricated, so we cut a piece of wood that can be attached to the neck pocket. We drill a hole in it too, so that we can hang it up. We’ll also put a screw in the rear strap button hole t...