Skip to main content

Posts

Showing posts with the label Touch

Touch Controlled Mute Switch Circuit Diagram

Here is another simple circuit to mute the volume of Audio devices through simple touch. It exploits the action of the flip-flops in the timer IC 555 to reduce the volume of the Audio amplifier. IC NE555 is designed in the toggle mode. Its lower and upper comparator inputs are connected to the touch plates which can be membrane switches or two pieces of conducting plates. The inputs of comparators are stabilized through R1 and R2 to avoid floating. Touch controlled Mute switch circuit diagram   When the touch plate connected to pin 2 is touched momentarily, output of IC1 goes high and T1 conducts. The centre tap of the volume control is connected to the collector of T1. So when T1 conducts current going to the amplifier drains through T1. This reduces the volume.IC1 remains latched in this position with LED on. When the touch plate connected to pin 6 is touched momentarily, output of IC1 goes low and T1 turns off. This restores the volume.

Build a Toggle Touch Switch Using Two Inverter Gates

We  can make a simple touch switch using only two inverter gates, two resistors, and two capacitors. The schematic diagram of the circuit is shown in the figure below. At power up, the output (of U1A) will be high, and the inverting output will be low because U1A gate will be triggered to ground level by C2. After triggered, the low level of U1A input is maintained by U1B output via R2. Toggle Touch Switch Using Two Inverter Gates Circuit Diagram If we touch the pad at this condition, where the output is high, then the U1A input will go high because we “short” the voltage of C1 to the input pin, and the low level previously caused by low level of U1B output voltage connected via R2 can’t be maintained because our skin resistance is much lower than 10M. After U1A input goes high then U1A output will go low, and now U1B will go high to maintain high voltage level of U1A via R2, so we can release our finger without loosing the last state. Touching the pad again after we release our pr...

Simple ON OFF Touch Switch with 555 Schematic

This simple ON OFF touch switch circuit is based on the well known timer IC 555 (IC1), which drives a relay that acts like a switch. The metal surfaces can have what form we want, but it should be clean and very close to the circuit. Read more  WC fan using 555 Touch plate MP1 in order to close the contact of relay RL1 [ON], or plate MP2 in order to open the contact of RL1 [OFF]. The Led D2 turns on when the contacts of RL1 are closed. Two small pieces of metal can be used as sensor plates. 555 ON/OFF Touch Switch Schematic     Parts List R1 = R2 = 3.3M R3 = 10K R4 = 1K C1 = 10nF D1 = 1N4007 Q1 = BC547 IC = NE555 12V relay Sourced By: Circuitsstream

555 Timer Travel Touch Alarm

The Travel Touch Alarm can be used to provide a audible alarm  when someone touches the door knob or handle of your hotel room. The door knob or handle must be made of metal for the circuit to work. The main chip in the circuit is a 555 timer which will be triggered if a hand comes close to or touches the door knob. 555 Timer Travel Touch Alarm Circuit Diagram The circuit attaches to the door knob at the end of the 1 meg ohm resistor. Once the timer is triggered the LED will light and the UJT will output a tone to the speaker. The timer will time out in 5 seconds. The sensitivity of the trigger can be changed by changing the 1 meg ohm resistor to another value. The 5 second time out can be adjusted by changing the value of the resistor connected between pin 8 and pin 7. The output tone can be changed by changing the RC values on the base of the UJT.

Touch Switch with Digital Output Circuit Diagram

This is a Touch Switch with Digital Output Circuit Diagram control key by touch simple, it uses a 4011 IC. The output logic HI has its pulse delay time controlled by C1. In the case is C1 4.7uF controls the pulse width for 1 second, then the touched the plate. Nothing prevents you from being done tests with other values ​​of C1. Touch Switch with Digital Output Circuit Diagram

D3 touch controller control color changing 12 volt led strip lights

DC12V , 4.4watt/feet, 18leds/feet, 16.4feet/reel. super bright leds, D3 touch controller link: http://www.superlightingled.com/d34a3ch-max-12a-dc1224v-d-series-rgb-touch-panel-highend-controller-for-rgb-color-change-multic-colour-led-strips-lighting-warranty-5-years-p-422.html RGB led strip lights link: http://www.superlightingled.com/rgb-flexible-led-strip-lights-c-3_26.html 100watt power supply link:  http://www.superlightingled.com/100w83a-dc12v-hulled-led-enclosed-switching-power-supply-with-builtin-pfc-p-210.html

Touch Based Blinking Lights

This circuit demonstrates the principle and operation of application based on touch sensor. The circuit is divided into three parts: Input, 555 timer and output. A touch plate is used for the input and output can be seen across an LED or a buzzer. Some application of the circuit include touch based blinking lights, touch buzzer, touch switch etc. The touch plates is connected to the trigger pin of the 555 timer IC. When we touch the touch plates the output of the touch plates becomes zero thereby providing an active low trigger to the IC 555. The IC is configured in the monostable mode .The output of the IC is a pulse whose frequency is set by the resistor (R1) and capacitor (C1) according to the formula [F=1/(1.1*R*C)]. In this case it produces a pulse with frequency of about 0.9 hertz and time period of 1.1 seconds. In monostable mode pin7 (discharge pin) and pin6 (threshold pin) are shorted while R1 is connected between pin7 and Vcc and C1 is connected between pin 6 and ground....