TREE

This tiny conductivity tester works with LM 3909. The tester makes a beeping sound if the resistance between the test probes between 0 and 100 O lies. Due to the volume of the beep, the resistance between the test probes can be determined. Audio Lm 3909 IC-conduction tester Circuit Diagram Parts List      R1 = 1 k      C1 = 10 uF      C2 = 100 nF      LS = Loudspeaker 12 to 16 Ω      IC1 = LM 3909

Circuit Diagram Description Here is the circuit diagram of three input microphone preamplifier. This is a mic mixer preamplifier centered on the high gain operational amplifier IC LM 348. This IC LM 348 is a quad operational amplifier IC that is it has four operational amplifiers embedded in this chip. This IC has also got some advanced features such as very high gain, class AB output stage and very low input supply current of 0.6 mA for each op-amp. The 3 channels of mic input require three amplifiers. The three op-amps (IC1b, IC1c and IC1d) out of four in the IC LM 348 are used here as input amplifiers for the corresponding channels. This three input amplifiers are made in this circuit work as non-inverting amplifiers. The operational amplifier IC1a is the output amplifier in this circuit. IC1a is wired as inverting amplifier here. The output from each input amplifiers are given to the inverting terminal of output op-amp. IC1a mixes the signals from each channel and produces the requ...

Hi everyone, today I will guide you how to make a powerful piano keyboard with LM555 IC. OK let's go! Piano keyboard description Here we will show how to build a piano keyboard which generate simple electronic keyboard musical notes DO, RE, MI, FA, SOL, LA, SI, DO1 and RE1, as shown in the following diagram (keyboard piano). Piano Keyboard with IC LM555 Piano keyboard operation circuit This circuit has a piano keyboard wave generator essentially comprises a 555 which operates as an astable multivibrator circuit. This type of operation is characterized by an output square wave of width defined by the designer. The outgoing wave frequency can be controlled by the resistor is connected between pins 7-8 and 2-7 in addition to the capacitor connected to pin 2 grounded. The resulting frequency can be calculated under the following equation. Where R eq is the result according to the push button is pressed on the keyboard piano. Therefore we can in our piano keyboard similar sound of an...

The TA7066P is original monolithic Intregated Circuit Audio Power Amplifier. Package IC is SIP10-16 and manufactered by TOSHIBA.  The above sequence is a series of low-grade intregated circuit amplifier , which was very small output . But this amplifier is very high impedance power output. For more details , see description below. Technical information : Min. Voltage   : 8   Volts DC Max. Voltage  : 25 Volts DC Max. Power    : 0,3 Watts Impedance      : 150 Ohms Min. Currents : 2,8 mA

This is a simple project Using IC NE 555 Voltage Inverter Circuit Diagram.In many circuits we need to generate an internal adjustable voltage. This circuit shows how it is possible to use a trusty old NE555 timer IC and a bit of external circuitry to create a voltage inverter and doubler. The input voltage to be doubled is fed in at connector K1. To generate the stepped-up output at connector K2 the timer IC drives a two-stage inverting charge pump circuit. The NE555 is configured as an astable multivibrator and produces a rectangular wave at its output, with variable mark-space ratio and variable frequency. This results in timing capacitor C3 (see circuit diagram) being alternately charged and discharged; the voltage at pin 2 (THR) of the NE555 swings between one-third of the supply voltage and two-thirds of the supply voltage. Voltage Inverter Circuit Using IC NE555  The output of the NE555 is connected to two voltage inverters. The first inverter comprises C1, C2, D1 and D2. The...

This Schematic use IC AN7102S , this is setereo amplifier and have output speaker 7,5 mW with impedance 32 Ohm . Supply need 1Volt to 3 Volt , wow this amplifier low voltage. You can use this amplifier on radio is use battery . With just one battery with voltage 1,5 Volt you can play this amplifier. See this Schematic below : Click to Enlarge Datasheet IC AN7102S Vcc                   =  1-3 V Pout                 = 2X 7,5 mW RL                    = 32 Ohm Ft                      = 20hz - 20Khz Icco                  = 7 mA Package         = DIP-18 Manufactered = MATSUSHITA

  *notif : this circuit is mono amplifier Anyone who uses this amplifier circuit would be surprised. Although this circuit has a small power output just 10 watts , but also issued a sound loud enough. At least match the transistor power amplifier with 60 watts. And his sound is good with low noise. Minimum voltage is 2 volt , and maximum voltage is 12 volt . Schematic circuit power amplifier AN7117 below : Click image to view Enlarge

 At this point is a Solar Charger Circuit to is used to charge information Acid otherwise Ni-album batteries using the solar energy power. The circuit harvests solar energy to charge a 6 volt 4.5 Ah rechargeable battery in favor of various applications. The stallion has Voltage and Current supervision and terminated voltage restrict sour facilities. Circuit uses a 12 volt solar panel and a changeable voltage supervisor IC LM 317 . The solar panel consists of solar cells each one rated on 1.2 volts. 12 volt DC is presented from the panel to charge the battery. Charging current passes through D1 to the voltage watchdog IC LM 317. By adjusting its Adjust pin, output voltage and current can subsist regulated. VR is placed amid the adjust pin and ground to provide an output voltage of 9 volts to the battery. Resistor R3 confine the charging current and diode D2 prevents discharge of current from the battery. Transistor T1 and Zener diode ZD conduct yourself having the status of a stop ...

This is the best IC LA 4440 Laptop Audio Amplifier circuit diagram, the audio output from the laptop’s built-in loudspeakers is low. A energy amplifier is needed to obtain a high volume. This is a simple circuit to amplify the laptop’s audio output. The circuit is made around energy amplifier IC LA 4440 (IC1) along with a couple of other components. LA4440 is really a dual funnel audio energy amplifier. Circuit diagram : Laptop Audio Amplifier Circuit Diagram It’s low distortion over an array of low to high wavelengths with good funnel separation. Built-in dual channels enable it for stereo system and bridge amplifier programs. In dual mode LA4440 gives 6 w per funnel as well as in bridge mode 19- watt output. It’s ripple rejection of 46 dB. The audio result can be recognized by utilizing two 6-watt loudspeakers. Connect hooks 2, 6 and ground of IC1 towards the stereo system jack which is combined with laptops. Assemble the circuit on the general-purpose PCB and enclose inside a appr...

See this circuit below: Datasheet IC TDA2004 Vcc                = 8-18 V Pout               = 2X 12 W RL                  = 2 Ohm Ft                   = 20hz - 20Khz Icco                = 65 mA Package         = SIP1-11 Manufactered = SGS-ATES Other IC TDA2004 , In this circuit you can use the following IC : A2000V A2005V TDA2005 TDA2005M MPC2005 Or you can call Persamaan IC TDA2004

General Description: The BA3837, BA3837F and BA3838F are ICs with an internal secondary active LPF for vocal cancellation functions and mixing amplifier functions with high degrees of vocal cancellation. Three control pins are used to switch between modes: the key controller input mode, through mode, vocal fader mode, sound multiplexing mode and mute mode. By offering these functions on a single chip, these ICs can significantly reduce the number of external components. Circuit diagram: Vocal fader IC Datasheet for BA3837: Download

This is Stereo Amplifier On this schematic amplifier circuit  use the ic AN7145L , but can use the following IC : AN7145M AN7145H AN7146M AN7146H You can use of all ic above. anthis circuit need suply voltage with dual voltage . Minimum voltage 6 Volt and maximum voltage 20 volt . Voltage just (-) and (+), but (-) can also ground. Maximum power output 2 X 20 watt with minimum impedance 4 ohm. Click image to view enlarge. You can operate this circuit with  plugging input to , PC or other media can give signal audio.

Circuit Diagram 7-Element Graphic Equalizer IC for Hi-Fi AN7337N Datasheet for AN7337N: Download

This circuit requires a voltage of 6-12 Volts. To have a good quality of this series with the voltage necessary suplly good too. The definition of good that is filtered and does not release much ripple voltage and using large-capacity condenser elco issued for the bass is strong enough. See below this circuit : Technical information about power amplifier with IC 5G37 Datasheet IC 5G31A Vcc                = 6-12 V Pout               = 0,4 W RL                 = 8 Ohm Ft                   = 40-17 Khz Icco               = 15 mA Package         = TABS1-14 Manufactered = China

Circuit Diagram:  Description Here is the circuit diagram of IC Controlled Emergancy Light With Charger or simply 12V to 220V AC inverter circuit. The circuit shown here is that of the IC controlled emergency light. Its main features are: automatic switching-on of the light on mains failure and battery charger with over-charge protection. When mains is absent, relay RL2 is in de-energized state, feeding battery supply to inverter section via its N/C contacts and switch S1. The inverter section comprises IC2 (NE555) which is used in stable mode to produce sharp pulses at the rate of 50 Hz for driving the MOSFETs. The output of IC2 is fed to gate of MOSFET (Q4) directly while it is applied to MOSFET (Q3) gate after inversion by transistor Q2. Thus the power amplifier built around MOSFETs Q3 and Q4 functions in push-pull mode. The output across secondary of transformer T2 can easily drive a 230-volt, 20-watt fluorescent tube. In case light is not required to be on during mains failure...

Power Supply This circuit is universal power supply , you can use this circuit to supply . On the IC you can adjustable regulator provides short circuit protection and automatic voltage adjust . The input voltage to the circuit regulator is supplyed by AC 220 V / 110 V and down voltage by transformator  then rectified by bridge diode . And output voltage is clear and stabilized . See Universal Power Spply Schematic below : Wiring a second LM317 , U2 , in parallel with U1 is a quick and clean way to increase the current limiting threshold to 3A without sacrifing short-circuit protection.When more than 3A is required , the regulator module can be used to drive the base of one or more pass-transisotrs.

In many circuits we need to generate an internal adjustable voltage. This circuit shows how it is possible to use a trusty old NE555 timer IC and a bit of external circuitry to create a voltage inverter and doubler. The input voltage to be doubled is fed in at connector K1. To generate the stepped-up output at connector K2 the timer IC drives a two-stage inverting charge pump circuit. The NE555 is configured as an astable multivibrator and produces a rectangular wave at its output, with variable mark-space ratio and variable frequency. This results in timing capacitor C3 (see circuit diagram) being alternately charged and discharged; the voltage at pin 2 (THR) of the NE555 swings between one-third of the supply voltage and two-thirds of the supply voltage.  Voltage Inverter Circuit Using IC NE555 The output of the NE555 is connected to two voltage inverters. The first inverter comprises C1, C2, D1 and D2. These components convert the rectangular wave signal into a nega...

This circuit operate with IC AN7156N . You just can use this IC , because hav'nt similarity it. In this Circuit have 2 input IN R and IN L and have Output R and L . Voltage supply require 15 V , minimum voltage 9 V and maximum voltage 24V . And the voltage must DC voltage , and better the DC voltage filtering . Maximum Output for 1 speaker 25 W , so this circuit have maximum output 2 X 25 W with minimum impedance 4 ohm. See this circuit schematic below : Click image to view enlarge

This is a simple timed beeper circuit diagram of beeper using 555 timer. This circuit can be employed to energize lights, horn, or other signaling device at any desired interval when the mercury switch is triggered. Since the current handling capability of mercury switch is not so high, an SCR is used to handle current drawn by the 555 timer circuit . Chose the SCR  current rating of 500mA at minimum to safely drive the 555 IC and the relay. The relay is not needed when the current drawn by alarm is less than 200mA, in this case the alarm can be installed to directly replace the relay coil.  Here is the schematic diagram of the circuit. 555-IC Timed Beeper Circuit Diagram