TREE

This is a simple Project of 12 V AC Dimmer Circuit Diagram. 12-V AC Dimmer Circuit Diagram The circuit described here is derived from a conventional design for a simple lamp dimmer, as you can see if you imagine a diac connected between points A and B. The difference between this circuit and a normal diac circuit is that a diac circuit won’t work at 12 V. This is the fault of the diac. Most diacs have a trigger voltage in the range of 30 to 40V, so they can’t work at 12 V, which means the dimmer also can’t work. 12-V AC Dimmer Circuit Diagram The portion of the circuit between points A and B acts like a diac with a trigger voltage of approximately 5.5 V. The network formed by R1, P1 and C1 generates a phase shift relative to the supply voltage. The ‘diac equivalent’ circuit outputs a phase-shifted trigger pulse to the triac on each positive and negative half-cycle of the sinusoidal AC voltage. This works as follows. First consider the positive half of the sine wave. C1 charges when the...

The strength supply routine structure is developed as a resource of continuous present with adverse heat range coefficient. Transistor Q1 (BD 140) is used as a heat range indicator. transistor Q2 is used to avoid the strength supply from discharging through R1 when strength is out of stock. Getting routine is developed depending on the LM350 present regulator IC. The result present of the battery charger can be altered between 13-15 V by various the POT R6. LM350 will try to keep the present decrease between the feedback pin and result pin at a continuous value of 1.25V. So there will be a continuous present circulation through resistor R1. Q1 act here as a heat range indicator with the help of R6/R3/R4 elements that are more or less manages the platform present of Q1. As relationship emitter / platform of transistor Q1, the same as other semiconductors, containing the heat range coefficient of-2mV / ° C, the present result will also display a bad heat range coefficient. This one is ju...

Power supply circuit to generate output below were variations between 1.3V DC to 12.2V DC with 1A current. In addition, the power supply circuit is also equipped with over-current protection or shield against belebih flow. Power supply circuit is very simple, but the quality is quite good, made ​​her basiccally regulator IC LM723 is a fairly legendary.

Valid schematic circuit diagrams of fluorescent lamps with a voltage source using 12 volt battery. This circuit 12 volt fluorescent lamp is very useful if the power goes out or can be used in a dark place with no electricity , but can use  the battery 12V . This 12V fluorescent lamp circuit i have tried and the results are bright , durable until decades. You can use 12Volt fluorescent lamps up to 40W . Use quality 12 Volt fluorescent lamp, do not use the fast heat , because the fast was also damage the transistor at 12Volt fluorescent lamp circuit . Do not occasionally mistaken in putting up the transistor . Description for 12 volt fluorescent lamp Circuit Diagrams : R1 = 220R/0.5W R2 = 1/0.5W C1 = 100n/100V C2 = 220uF/50V Q1 = D1885/D1710 A/B= To A fluorescent lamp/ and B to B fluorescent Lamp and just use one pin B = Battery 12 volt with currents above 5A Roll of copper wire on ferrite rod, with : L1 = 1.2 mm diameter wire with many loops winding 20 times L2 = 1.2mm di...

The BVM1 is an ultra low power ten LED battery voltmeter circuit that is optimized for monitoring solar-charged 12V battery systems. The circuit features an expanded meter scale that displays ten color-coded voltage steps from 10.5V to 15.0V. Power is conserved by only turning on the appropriate LED for a short but bright flash once every 1.25 seconds. The LED display can be turned on continuously (no blinking) by turning the Calibrate switch on, more battery power is consumed in this mode. BVM1-12 Volt Battery Voltage Monitor With Parts List  The BVM1 also includes a battery low voltage beeper that warns when the battery voltage drops below a preset voltage. The beeper can be turned on and off with the L.V. Beep Activate switch. The BVM1 is protected against reverse voltage connection and is fused for safety. The design goals of this circuit were efficiency, simplicity, reliability and the use of field replaceable parts. The BVM1 circuit has been designed to work in conjunction w...

Using LT3582 -12 dual channel DC DC converter integrated circuit, manufactured by Linear Technology, can be designed a very simple step up dc converter. This 5 to 12V c converter electronic project provide both positive and negative outputs required in many biasing applications such as active matrix OLED (organic light-emitting diode)displays as well as CCD (charge coupled device) applications. The LT3582 offer an I2C interface that can dynamically program output voltages, power sequencing and output voltage ramps as the application requires. The LT3582’s positive output voltage can be set between 3.2V and 12.775 in 25mV steps, whereas the negative output can be set between -1.2V and -13.95V in 50mV steps. The LT3582-12 is preconfigured with ±12V output, requiring no future programming.

DC12V , 4.4watt/feet, 18leds/feet, 16.4feet/reel. super bright leds, D3 touch controller link: http://www.superlightingled.com/d34a3ch-max-12a-dc1224v-d-series-rgb-touch-panel-highend-controller-for-rgb-color-change-multic-colour-led-strips-lighting-warranty-5-years-p-422.html RGB led strip lights link: http://www.superlightingled.com/rgb-flexible-led-strip-lights-c-3_26.html 100watt power supply link:  http://www.superlightingled.com/100w83a-dc12v-hulled-led-enclosed-switching-power-supply-with-builtin-pfc-p-210.html

Power Supply in this article use a regulator that is composed of 2 pieces of NPN transistor. A transistor acts as a power regulator and a transistor again serves as a controller output voltage. Power Supply has an adjustable output with a range of 6-12 VDC. The part that serves as a power regulator is Q1 TIP31. Then the controller output voltage is a voltage divider composed of R3, R4, VR1 and R2 provide bias to the base of Q2 to Q1 mengentrol power regulator. In a series of power supply is mounted 5.1 V zener diode which serves to make the minimum limit the output voltage with Q2. Adjustable Power Supply with transistor circuit Power Supply With transistor circuit is quite simple and can be made with the PCB holes, so for those who want to try to directly mempraktikannya. May the power supply circuit can be useful for readers, especially for friends who need a power supply circuit with the regulator transistor.