TREE

This tiny conductivity tester works with LM 3909. The tester makes a beeping sound if the resistance between the test probes between 0 and 100 O lies. Due to the volume of the beep, the resistance between the test probes can be determined. Audio Lm 3909 IC-conduction tester Circuit Diagram Parts List      R1 = 1 k      C1 = 10 uF      C2 = 100 nF      LS = Loudspeaker 12 to 16 Ω      IC1 = LM 3909

TPA3122D2 Class D Audio Amplifier TPA3122D2 IC is used as a class D audio amplifier and can deliver up to 15W of power at 10% distortions. The real advantage of using a class D amp, especially TPA3122 is the fact that this IC doesn’t need a heatsink because it has a high efficiency. Another great thing about it is that you can buy a $20 built-it-yourself kit or even cheaper from ebay but you need to be careful not to buy a fake one. TPA3122D2 Class D Audio Amplifier I discovered this IC while searching for an audio amplifier circuit that I need for the 2 x 10W/4Ω speakers received from my brother-in-law. I think that TPA3122 can provide enough power for what I need even though it can output only 8W with 1% distortions on a 4Ω speaker (something that some of you might find too low). The main reason I would choose this instead of a class A or B IC is the fact it doesn’t need a heatsink, so the whole amplifier will be lighter in weight and cheaper.

This is the schematic diagram of 3 channels audio splitter amplifier circuit which built using op-amp IC TL084. The 3 channels amplifier output distribution applies a single TL084.   3 Channels Audio Splitter Amplifier Circuit Diagram The very first step is to capacitive coupling having a p. 1.0 ~ electrolytic capacitor. The entries are railways Vee Y2 or 4.5 V. This enables working with an individual 9V power source. A voltage gain of 10 (1 M?/100 Kohm) is obtained in the first stage, as well as the other three floors are connected as a unity gain voltage followers. Every single output stage drives independently through an amplifier output 50 pF capacitor towards the resistance of 5.1 k ohm load. The response range is flat from 10 Hz to 30 kHz.

This is use the MOSFET power amplifier circuit, amplifier circuit has a very good sound quality. With the noise is quite small, thus making the amplifier circuit is suitable for you to try. Here's the circuit. Click to view larger.  Power amplifier with a 70Watt power is able to issue a clear voice, and very and good loud.

25 Watt Audio Amplifier Circuits Diagram Parts: R1 ,R4 _________47K   1/4W Resistors R2____________ 4K7   1 /4W Resistor R3____________ 1K5   1 /4W Resistor R5__________390R    1/4W Resistor R6__________470R    1/4W Resistor R7___________33K    1/4W Resistor R8__________150K    1/4W Resistor R9___________15K    1/4W Resistor R10__________27R    1/4W Resistor R11_________500R    1/2W Trimmer Cermet R12 ,R13,R16 __10R    1/4W Resistors R14 ,R15 _____220R    1/4W Resistors R17___________8R2     2W Resistor R18____________R22    4W Resistor ( wirewound )   C1___________ 470nF   63V Polyester Capacitor C2___________ 330pF   63V Polystyrene Capacitor C3 ,C5 ________470µF   63V Electrolytic Capacitors C4 ,C6,C8,C11 _100nF   63V Polyester Capacitors C7___________100µ F   25V Electrolytic Capacitor C9____________ 10pF   63V Polys...

This is a circuit of SA58672 Small Class-D Audio Amplifier. This circuit is suitable for mobile device. It has maximum output power of 3.0 W for a 4ohm load and 1.7W for 8ohm load with power supply of 5V. If we uses 3.6 V power supply, the maximum output power is 900mW with 8ohm load. Here is the circuit : Using 9-bump Wafer Level Chip Scale Package (WLCSP), the SA58672UK save space in portable designs, because it measures only 1.66 x 1.71 x 0.6 mm. This circuit produces better overall audio performance because it has improved RF rectification and immunity to noise. The SA58672UK is suitable for cellular handsets or wireless and other portable audio application because it has fast start-up time of 7 ms eliminates pop-on sounds. [Source: NXP Application Note]

 Description A very simple TV audio video transmitter circuit can be constructed using this schematic diagram . This TV audio video transmitter circuit can be used to transmit video signals from VCR ( or some other device ) to a TV without using any cable . Video signals input at jack J1 are first terminated by resistor R6 and coupled through capacitor C1 to clamping-diode D1. Potentiometer R3 is used to set the gain of the video signal; its effect is similar to that of the contrast control on a TV set. Bias-control R7 can be used to adjust the black level of the picture so that some level of signal is transmitted, even for a totally dark picture. RF-transformer T1 and its internal capacitor form the tank circuit of a Hartley oscillator that's tuned to 4.5 megahertz. Audio signals input at J2 are coupled to the base of Q3 via C2 and R4: the audio signal modulates the base signal of Q3 to form an audio subcarrier that‚s 4.5-megahertz higher than the video-carrier frequency. The FM ...

I have built this amplifier and it does sound good. It requires a preamp as it hasn't got much gain. It requires big heat sinks and a large transformer and a great power supply and careful wiring, but in the end it is xtremely simple and it sounds very good. The zener diode rejects any ripple coming from the power supply, But you still only want a ripple of 10mV max. The ripple reaching the input is amplified, so the zener diode gets rid of that, but whatever ripple there is will still reach the power stage.

This design is based on the 18 Watt Audio Amplifier , and was developed mainly to satisfy the requests of correspondents unable to locate the TLE2141C chip. It uses the widespread NE5532 Dual IC but, obviously, its power output will be comprised in the 9.5 - 11.5W range, as the supply rails cannot exceed ±18V. 10 W Audio Amplifier Circuit Diagram As amplifiers of this kind are frequently used to drive small loudspeaker cabinets, the bass frequency range is rather sacrificed. Therefore a bass-boost control was inserted in the feedback loop of the amplifier, in order to overcome this problem without quality losses. The bass lift curve can reach a maximum of +16.4dB @ 50Hz. In any case, even when the bass control is rotated fully counterclockwise, the amplifier frequency response shows a gentle raising curve: +0.8dB @ 400Hz, +4.7dB @ 100Hz and +6dB @ 50Hz (referred to 1KHz). Notes: Can be directly connected to CD players, tuners and tape recorders. Schematic shows left channel only, but C...

6 Watt Audio Amplifier Schematic Circuit with TDA1519 The audio amplifier circuit is on the TDA1519 amplifier IC that is based in audio applications, which is not a aerial achievement ability can be used. The ambit TDA1519 is a ability of 2×6 watts. The TDA1519 is an amplifier congenital Class B dual-output advance in a 9-by-line (SIL) artificial amalgamation boilerplate achievement is primarily developed for car radio applications. Key Features of the audio amplifier IC TDA1519 are: Requires few alien components, anchored gain, acceptable bounce drive, aphasiac / standby mode, thermal protection, about-face polarity safe. Tda1519 amplifier ability rating, 14.4 volts.

Simple Automatic Switch For Audio Power Amplifier. Circuit of an automatic switch for audio power amplifier stage is presented here. The circuit uses stereo preamplifier output to detect the presence of audio to switch the audio power amplifier on only when audio is present. The circuit thus helps curtail power wastage. IC1 is used as an inverting adder. The input signals from left and right channels are combined to form a common signal for IC2, which is used as an open loop comparator. IC3 (NE556) is a dual timer. Its second section, i.e., IC3(b), is configured as monostable multivibrator. Output of IC3(b) is used to switch the power amplifier on or off through a Darlington pair formed by transistors T1 and T2. IC3(a) is used to trigger the monostable multivibrator whenever an input signal is sensed. Circuit diagram: Automatic Switch For Audio Power Amplifier Circuit Diagram Under ‘no signal’ condition, pin 3 of IC2 is negative with respect to its pin 2. Hence the output of IC2 is lo...

The TA7066P is original monolithic Intregated Circuit Audio Power Amplifier. Package IC is SIP10-16 and manufactered by TOSHIBA.  The above sequence is a series of low-grade intregated circuit amplifier , which was very small output . But this amplifier is very high impedance power output. For more details , see description below. Technical information : Min. Voltage   : 8   Volts DC Max. Voltage  : 25 Volts DC Max. Power    : 0,3 Watts Impedance      : 150 Ohms Min. Currents : 2,8 mA

The target of this project was the design of a small portable mixer supplied by a 9V PP3 battery, keeping high quality performance. The mixer is formed assembling three main modules that can be varied in number and/or disposition to suit everyone needs. The three main modules are: Input Amplifier Module: a low noise circuit equipped with a variable voltage-gain (10 - 100) preset, primarily intended as high quality microphone input, also suitable for low-level line input. Tone Control Module: a three-band (Bass, Middle, Treble) tone control circuit providing unity-gain when its controls are set to flat frequency response. It can be inserted after one or more Input Amplifier Modules and/or after the Main Mixer Amplifiers. Main Mixer Amplifier Module: a stereo circuit incorporating two virtual-earth mixers and showing the connection of one Main Fader and one Pan-Pot. The image below shows a Block diagram of the entire mixer featuring four Input Amplifier Modules followed by four in-out...

A 60-dB Range Compressor circuit shown in the schematic diagram below can produce consistent output of 1.4V P-P over entire 60dB range that is very useful for audio level/volume stabilization.  As the main components, this circuit uses a 741 opamp and JFET. With input range of 20mV to 2oV, this circuit has delay time of 0.4s (decay time)  and response time of 1.2ms (attack time). The JFET is used as  voltage-controlled resistor in peak-detecting control loop of 741 opamp. Here is the schematic diagram of the circuit.  A 60-dB Range Compressor schematic diagram

This audio peak detector allows a pair of stereo channels to be monitored on a sin-gle LED. Identical circuitry is used in the left and right channels. Use is made of the switch-ing levels of Schmitt trigger NAND gates inside the familiar 4093 IC. The threshold level for gate IC1.A (IC1.B) is set with the aid of preset P1, which supplies a high-impedance bias level via R2 (R1).  Audio Top Detector Circuit diagram :   Simple Audio Peak Detector Circuit Diagram  When, owing to the instantaneous level of the audio signal superimposed on the bias voltage by C3 (C2), the dc level at pins 1 and 2 (5 and 6) of the Schmitt trigger gate drops below a certain level, the output of IC1.A (IC1.B) will go High. This level is copied to the input of IC1.C via D2 (D1) and due to the inverting action of IC1.C, LED D3 will light. Network R3-C1 provides some delay to enable very short audio peaks to be reliably indicated. Initially turn the wiper of P1 to the +12 V extreme — LED D3 should ...

Circuit diagram: AM FM radio reciver circuit diagram Datasheet for TDA1083: Download

This Schematic use IC AN7102S , this is setereo amplifier and have output speaker 7,5 mW with impedance 32 Ohm . Supply need 1Volt to 3 Volt , wow this amplifier low voltage. You can use this amplifier on radio is use battery . With just one battery with voltage 1,5 Volt you can play this amplifier. See this Schematic below : Click to Enlarge Datasheet IC AN7102S Vcc                   =  1-3 V Pout                 = 2X 7,5 mW RL                    = 32 Ohm Ft                      = 20hz - 20Khz Icco                  = 7 mA Package         = DIP-18 Manufactered = MATSUSHITA

This audio power amplifier project is based on LM1875 amplifier module from National Semiconductor. It can deliver up to 30W of power using an 8 ohm load & dual 30V DC power supplies. It is designed to operate with maximum outside parts with current limit & thermal shutdown protection features . Other features include high gain, quick slew rate, wide power supply range, giant output voltage swing & high current capability. Summary of the audio amply-fire features: Low distortion: 0.015%, 1 kHz, 20 W Wide power bandwidth: 70 kHz Wide supply range 16V-60V Up to 30 watts output power Internal output protection diodes Protection for AC & DC short circuits to ground 94 dB ripple rejection Plastic power package TO-220 25V Power Supply The schematic below shows how the +25V DC & -25V DC are obtained. In order to provide power supply for two stereo amplifiers, a power transformer rating of 80VA with 240V/36V middle tapped secondary winding is used. The secondary output of ...

Description: The AN7177 is a monolithic integrated circuit designed for   Dual BTL audio power amplifier suitable for Hi-Fi and car  stereo.  Features:  High output power (20W x 2)   Incorporating stand-by circuits   Low shock noise from power ON/OFF switching   Fewer external components   Incorporates protection circuits   Highly stable operation Circuit Diagram: Dual BTL 20W Audio Power Amplifier  Datasheet for AN7177:  Download

This is a schematic of a 10W stereo audio amplifier using TDA2009A amplifier IC. TDA2009A is a good IC provides quality sound. It has built in features like output current protection and thermal protection etc. The circuit can be operate between 8 to 24V DC with 1 to 2 amphere. 10W Stereo Audio Amplifier Circuit Diagram : If you want to operate this 10 watt amplifier circuit with watt amplifier circuit with mains supply then use a filtered and stable power supply to reduce mains hum. 10 watt out put power can be obtained by providing 20V 1.5A to the circuit. Use good and thick heatsink with the IC.