12V To 24V DC DC Converter Circuit Diagram

This is a simple project of 12V To 24V DC-DC Converter Circuit Diagram.This simple 12V To 24V DC-DC Converter Circuit Diagram can provide up to 24V from a 12V source. It can be used to run radios, small lights, relays, horns and other 24V accessories from a 12V vehicle with a maximum draw of about 800mA.

It can be used to charge one 12V battery from another, or step up the voltage just enough to provide necessary overhead for a 12V linear regulator. Using one op-amp as a square wave oscillator to ring an inductor and another op-amp in a feedback loop, it won't drift around under varying loads, providing a stable 24V source for many applications. With a wide adjustment in output this circuit has many uses.

12V To 24V DC-DC Converter Circuit Diagram

Parts

Part	Total Qty.	Description	Substitutions
R1, R2, R3, R4, R8, R7	6	100K 1/4W Resistor
R5	1	470 Ohm 1/2W Resistor
R6	1	10K Linear Pot
C1	1	0.01uF Mylar Capacitor
C2	1	0.1uF Ceramic Disc Capacitor
C3	1	470uF 63V Electrolytic Capacitor
D1	1	1N4004 Rectifier Diode
D2	1	BY229-400 Fast Recovery Diode	See Notes
Q1	1	BC337 NPN Power Transistor
U1	1	LM358 Dual Op Amp IC
L1	1	See Notes
MISC	1	Board, Wire, Socket For U1, Case, Knob For R6, Heatsink for Q1

Notes

R6 sets the output voltage. This can be calculated by Vout = 12 x (R8/(R8+R7)) x (R6B/R6A).
L1 is made by winding 60 turns of 0.63MM magnet wire on a toroidial core measuring 15MM (OD) by 8MM (ID) by 6MM (H).
D2 can be any fast recovery diode rated at greater then 100V at 5A. It is very important that the diode be fast recovery and not a standard rectifier.
Q1 will need a heatsink.

Sourced By Circuitsstream

Comments

3 Channels Audio Splitter Amplifier Circuit Diagram using TL084

This is the schematic diagram of 3 channels audio splitter amplifier circuit which built using op-amp IC TL084. The 3 channels amplifier output distribution applies a single TL084. 3 Channels Audio Splitter Amplifier Circuit Diagram The very first step is to capacitive coupling having a p. 1.0 ~ electrolytic capacitor. The entries are railways Vee Y2 or 4.5 V. This enables working with an individual 9V power source. A voltage gain of 10 (1 M?/100 Kohm) is obtained in the first stage, as well as the other three floors are connected as a unity gain voltage followers. Every single output stage drives independently through an amplifier output 50 pF capacitor towards the resistance of 5.1 k ohm load. The response range is flat from 10 Hz to 30 kHz.

Apples Next iPhone to Arrive Sept 10

Apple will unveil the next edition of the iPhone at a major press event on Sept. 10, according to All Things D.Other than the purported date for the unveiling of the so-called iPhone 6, the site's Ina Fried did not offer any details about what else we might expect from Apple with the arrival of the company's first new smartphone since the debut of the iPhone 5 last September. If Apple does lift the curtain on its next-generation iPhone on Sept. 10, it would be two days short of a full year since the iPhone 5 was revealed. While Apple CEO Tim Cook is rumored to be under pressure from Apple's board to step up the pace of innovation and product release schedules, that lag between new iPhone releases wouldn't be particularly unusual for the company—Apple went 16 months between introducing the iPhone 4 and iPhone 4S , for example. But as Fried noted, even as Apple has continued to enjoy robust sales of the iPhone this year, the company has seen its overall share of the gl...

RF amplifier protection

RF amplifier protection I have developed the protection circuit for the EB104 amplifier I am working on, after I finally had some time to design and test a few models. The main requirements have been: - protection in case of high temperature; - protection in case of high SWR; - protection in case of wrong output filter selection; - simple design (i’m a fan of the whole K.I.S.S. rule of thought), able to work in strong electromagnetic fields, reliable, inexpensive. Because i will be using the same directional coupler i have used in the SWR meter (the one made on PCB) wich is directly influenced by the signal frequency, and because i want full HF coverage, i cannot just measure the reflected signal and make a circuit cut the amplifier when it goes over a limit; on 28Mhz the coupler generates roughly 4 times more voltage that let’s say in 7Mhz. So a system that compares direct and reflected signal and triggers when the latter is percentually too high was needed, therefore an operational a...

TREE

Search This Blog