Laptop Audio Amplifier IC LA 4440

This is the best IC LA 4440 Laptop Audio Amplifier circuit diagram, the audio output from the laptop’s built-in loudspeakers is low. A energy amplifier is needed to obtain a high volume. This is a simple circuit to amplify the laptop’s audio output. The circuit is made around energy amplifier IC LA 4440 (IC1) along with a couple of other components. LA4440 is really a dual funnel audio energy amplifier.

Circuit diagram :

Laptop Audio Amplifier Circuit Diagram

It’s low distortion over an array of low to high wavelengths with good funnel separation. Built-in dual channels enable it for stereo system and bridge amplifier programs. In dual mode LA4440 gives 6 w per funnel as well as in bridge mode 19- watt output. It’s ripple rejection of 46 dB. The audio result can be recognized by utilizing two 6-watt loudspeakers.

Connect hooks 2, 6 and ground of IC1 towards the stereo system jack which is combined with laptops. Assemble the circuit on the general-purpose PCB and enclose inside a appropriate cabinet. The circuit works off controlled 12V power supply. It’s suggested to make use of audio input socket within the circuit board. Make use of a proper warmth-sink for LA4440.

Comments

Build a 3000W Stereo Power Amplifier Circuit Diagram

How to Build a 3000W Stereo Power Amplifier Circuit Diagram? Lets start first we define 3000wstereo power amplifier circuit diagram this circuit has a power output of up to 1500W RMS power amplifier circuit is often used to power sound systems spelunker for outdor. In the final image can be seen a series of power amplifiers using 10 sets of power transistors for the ending. This power amplifier circuit using a transistor amplifier from the front, signal splitter, driver and power amplifier. Current consumption required is quite large power amplifier that is 15-20 A 1500W power amplifier circuits for this. Supply voltage needed by the power of this amplifier is the optimal working order symmetrical 130VDC (130VDC-130VDC ground). 1500W amplifier circuit below is a picture series of mono, stereo if you want to make it necessary to make two copies of the circuit. For more details can be viewed directly image the following 1500W power amplifier circuit. The series of High Power Amplifier 15

Solid State Switch For Dc Operated Gadgets

This solid state DC switch can be assembled using just three transistors and some passive components. It can be used to switch on one gadget while switching off the second gadget with momentary operation of switch. To reverse the operation, you just have to momentarily depress another switch. The circuit operates over 6V-15V DC supply voltage. It uses positive feedback from transistor T2 to transistor T1 to keep this transistor pair in latched state (on/ off), while the state of the third transistor stage is the complement of transistor T2’s conduction state. Initially when switch S3 is closed, both transistors T1 and T2 are off, as no forward bias is available to these, while the base of transistor T3 is effectively grounded via resistors R8 and R6 (shunted by the load of the first gadget). As a result, transistor T3 is forward biased and gadget 2 gets the supply. This is indicated by glowing of LED2. Circuit diagram : Solid-State Switch For Dc-Operated Gadgets Circuit Diagram Whe

Amplifier Circuit 2 X 10 watt with IC AN7145

This is Stereo Amplifier On this schematic amplifier circuit use the ic AN7145L , but can use the following IC : AN7145M AN7145H AN7146M AN7146H You can use of all ic above. anthis circuit need suply voltage with dual voltage . Minimum voltage 6 Volt and maximum voltage 20 volt . Voltage just (-) and (+), but (-) can also ground. Maximum power output 2 X 20 watt with minimum impedance 4 ohm. Click image to view enlarge. You can operate this circuit with plugging input to , PC or other media can give signal audio.

TREE

Search This Blog