Skip to main content

TDA1562Q 54 W Amplifier Circuit Diagram


This is the simple Using TDA1562Q 54 W Amplifier Circuit Diagram. The integrated output amplifier described in this article consists of little more than one integrated circuit. It is intended especially for use in motor vehicles and other battery operated applications. Although it appears simple and hardly worth looking at, the amplifier can produce an appreciable audio power output.[link]

Using TDA1562Q 54 W Amplifier Circuit Diagram


Using TDA1562Q 54 W Circuit Diagram



Data
PropertiesHigh power output through Class-H operation
Low power dissipation during reproduction of music signals
Proof against short-circuits
Protection against excessive temperatures
Standby switch
No power-on or power-off clicks
Visible error indication
Measurement results (at Ub=14.4 V)
Supply voltage 8–18 V
Sensitivity 760 mV r.m.s.
Input impedance 70 kΩ
Power output 54 W r.m.s.
into 4 Ω (f=1 kHz; THD+N=1%)
Harmonic distortion (THD+N) at 1 W into 4 Ω: 0.046% (1 kHz)
0.29% (20 kHz)
at 35 W into 4 Ω: 0.12% (1 kHz)
0.7% (20 kHz)
Signal-to-noise ratio (with 1 W into 4 Ω) 88 dBA
Power bandwidth 7.5 Hz – 185 kHz (at 25 W into 4 Ω)
Quiescent current about 135 mA (‘on’)
COMPONENTS LIST
Resistors:
R1 = 1MΩ
R2 = 4kΩ7
R3 = 1kΩ
R4 = 100kΩ
Capacitors:
C1,C2 = 470nF
C3,C4 = 10μF 63V radial
C5,C6,C8 = 4700μF 25V radial
(18mm max. dia., raster 7.5 mm)
C7 = 100nF, raster 5 mm
Semiconductors:
D1 = high-efficiency-LED
IC1 = TDA1562Q (Philips)
Miscellaneous:
S1 = single-pole on/off switch
Four spade connectors, PCB mount
Heatsink for IC1 (Rth<2.5>

Comments

Popular posts from this blog

A basic Arduino Solar PV Monitor

I have just recently had solar pv installed, mainly to future proof my energy costs, I do not expect it to be like drilling for oil in my back garden, however the return looks to be encouraging. The install gives you another single unit meter, from this you will see the total amount the panels produce, but that is about it. I wanted to know how much the production was as it was happening, I discovered the light blinks on the front of the meter will flash 1000 times for each kWh of electricity which passes through. The rate of the flashing of the LED tells you how much power is currently passing through the meter. [ ]

Schematic Audio Amplifier with IC AN7102S

This Schematic use IC AN7102S , this is setereo amplifier and have output speaker 7,5 mW with impedance 32 Ohm . Supply need 1Volt to 3 Volt , wow this amplifier low voltage. You can use this amplifier on radio is use battery . With just one battery with voltage 1,5 Volt you can play this amplifier. See this Schematic below : Click to Enlarge Datasheet IC AN7102S Vcc                   =  1-3 V Pout                 = 2X 7,5 mW RL                    = 32 Ohm Ft                      = 20hz - 20Khz Icco                  = 7 mA Package         = DIP-18 Manufactered = MATSUSHITA