Long range FM voice Transmitter circuit

This circuit shows how to build a super-sensitive, mini-powered FM transmitter consisting of a RF (radio Frequency) oscillator section interfaced with a high sensitivity, wide pass-band audio amplifier and capacitance mike with a built-in FET (Field Effect Transistor) that modulates the base of the RF oscillator transistor. Transistor Q1 forms a relatively stable RF oscillator whose frequency and is determined by the value of coil L1 and turning capacitor C4.

Part List :

R1_______15K

R2_______3K9

R3_______220R

R4,R5____1K

R6,R9____10K

R7_______390K

C1,C6____0.01uF

C2_______4.7pF

C3_______0.1uF

C4_______6-35pf trimmer cap

C5_______2.2uF

B1_______3V

L1_______Coil winding (see below)

Q1,Q2____PN2222

M1_______Special FET bypassed microphone

Assemble L1 :
Form L1 by tightly wrapping eight turns of #16 bus wire on a #8 wood screw. Produces an eight-turn coil with an inner diameter of approximately 0.135 inches and lenght of about 0.625 inches. Insert in the proper hole and solder as shown.

Comments

3 Channels Audio Splitter Amplifier Circuit Diagram using TL084

This is the schematic diagram of 3 channels audio splitter amplifier circuit which built using op-amp IC TL084. The 3 channels amplifier output distribution applies a single TL084. 3 Channels Audio Splitter Amplifier Circuit Diagram The very first step is to capacitive coupling having a p. 1.0 ~ electrolytic capacitor. The entries are railways Vee Y2 or 4.5 V. This enables working with an individual 9V power source. A voltage gain of 10 (1 M?/100 Kohm) is obtained in the first stage, as well as the other three floors are connected as a unity gain voltage followers. Every single output stage drives independently through an amplifier output 50 pF capacitor towards the resistance of 5.1 k ohm load. The response range is flat from 10 Hz to 30 kHz.

Apples Next iPhone to Arrive Sept 10

Apple will unveil the next edition of the iPhone at a major press event on Sept. 10, according to All Things D.Other than the purported date for the unveiling of the so-called iPhone 6, the site's Ina Fried did not offer any details about what else we might expect from Apple with the arrival of the company's first new smartphone since the debut of the iPhone 5 last September. If Apple does lift the curtain on its next-generation iPhone on Sept. 10, it would be two days short of a full year since the iPhone 5 was revealed. While Apple CEO Tim Cook is rumored to be under pressure from Apple's board to step up the pace of innovation and product release schedules, that lag between new iPhone releases wouldn't be particularly unusual for the company—Apple went 16 months between introducing the iPhone 4 and iPhone 4S , for example. But as Fried noted, even as Apple has continued to enjoy robust sales of the iPhone this year, the company has seen its overall share of the gl...

RF amplifier protection

RF amplifier protection I have developed the protection circuit for the EB104 amplifier I am working on, after I finally had some time to design and test a few models. The main requirements have been: - protection in case of high temperature; - protection in case of high SWR; - protection in case of wrong output filter selection; - simple design (i’m a fan of the whole K.I.S.S. rule of thought), able to work in strong electromagnetic fields, reliable, inexpensive. Because i will be using the same directional coupler i have used in the SWR meter (the one made on PCB) wich is directly influenced by the signal frequency, and because i want full HF coverage, i cannot just measure the reflected signal and make a circuit cut the amplifier when it goes over a limit; on 28Mhz the coupler generates roughly 4 times more voltage that let’s say in 7Mhz. So a system that compares direct and reflected signal and triggers when the latter is percentually too high was needed, therefore an operational a...

TREE

Search This Blog