Build a Beeper visual indicator Circuit Diagram

This entire circuit of beeper cum visual indicator is build and fabricated around two timer ICs and is configured in an astable multivibrator mode. The frequency generated by IC₁ is controlled by capacitor C₁. The output from pin 3 of IC₁ is given to input pin 4 of IC₂ and base of voltage amplifier transistor T₁through resistor R₄. Flashing light is connected to collector of switching transistor T₂ and grounded through resistor R₇.

The output of IC₂ is obtained from pin 3 and is given to base of power amplifier transistor T₃ used to drive 8-ohm speaker connected to the collector.

NOTE: LED can be replaced with 3V to 12V DC bulb after eliminating resistor R₇.

Beeper visual indicator Circuit Diagram

PARTS LIST

Resistors (all ¼-watt, ± 5% Carbon)

R_1,R7 = 330 Ω

R₂ = 6.8 KΩ

R₃ = 5.6 KΩ

R₄ = 47 KΩ

R₅, R₆ = 22 KΩ

Capacitors

C₁ = 100 µF/10V electrolytic

C₂, C₄ = 0.1 µF ceramic disc

C₃ = 0.01 µF ceramic disc

C₅ = 1000 µF/25V electrolytic

Semiconductors

IC₁, IC₂ = NE555 (Timer IC)

T₁ = BC148B

T₂ = SK100

T₃ = SL100B

Miscellaneous

SW₁ = Push-To-On switch

LS₁ = 8-ohm loudspeaker

LED₁ = Flashing LED

Comments

3 Channels Audio Splitter Amplifier Circuit Diagram using TL084

This is the schematic diagram of 3 channels audio splitter amplifier circuit which built using op-amp IC TL084. The 3 channels amplifier output distribution applies a single TL084. 3 Channels Audio Splitter Amplifier Circuit Diagram The very first step is to capacitive coupling having a p. 1.0 ~ electrolytic capacitor. The entries are railways Vee Y2 or 4.5 V. This enables working with an individual 9V power source. A voltage gain of 10 (1 M?/100 Kohm) is obtained in the first stage, as well as the other three floors are connected as a unity gain voltage followers. Every single output stage drives independently through an amplifier output 50 pF capacitor towards the resistance of 5.1 k ohm load. The response range is flat from 10 Hz to 30 kHz.

A basic Arduino Solar PV Monitor

I have just recently had solar pv installed, mainly to future proof my energy costs, I do not expect it to be like drilling for oil in my back garden, however the return looks to be encouraging. The install gives you another single unit meter, from this you will see the total amount the panels produce, but that is about it. I wanted to know how much the production was as it was happening, I discovered the light blinks on the front of the meter will flash 1000 times for each kWh of electricity which passes through. The rate of the flashing of the LED tells you how much power is currently passing through the meter. [ ]

RF amplifier protection

RF amplifier protection I have developed the protection circuit for the EB104 amplifier I am working on, after I finally had some time to design and test a few models. The main requirements have been: - protection in case of high temperature; - protection in case of high SWR; - protection in case of wrong output filter selection; - simple design (i’m a fan of the whole K.I.S.S. rule of thought), able to work in strong electromagnetic fields, reliable, inexpensive. Because i will be using the same directional coupler i have used in the SWR meter (the one made on PCB) wich is directly influenced by the signal frequency, and because i want full HF coverage, i cannot just measure the reflected signal and make a circuit cut the amplifier when it goes over a limit; on 28Mhz the coupler generates roughly 4 times more voltage that let’s say in 7Mhz. So a system that compares direct and reflected signal and triggers when the latter is percentually too high was needed, therefore an operational a...

TREE

Search This Blog