Transmitter Received AM radio

AM Transmitter circuit

To this powerful AM transmitters are huge, using ceramic tuning 3.587 mhz resonator and resonator filters are also sold with a value of 5.5 mhz, 7.7 mhz and 10.7 mhz. Distance transmitter range is approximately 2-4 km. the working principle of this circuit are filter resonator/ceramic filters raise the frequency of the value of the resonator filter.

This frequency is amplified by the transistor can be changed t1. Frequency so need C7 as a regulator / placement. sound signal superimposed over the audio transformer.frekuensi which awakened by resonator filters and t1 is fed to the next amplify strengthened so as to achieve the desired power passed to antenna. t2 and t3 as a buffer as a final power amp.

AM Transmitter Schematics

AM radio / receiver circuit

For AM radio because it's hard to find IC ZN 414 then now could be replaced with the equivalent of IC MK 484. Frequency coverage between 550 kHz-1600 mhz, 3 pins of this IC include series of radio tuner, RF amplifiers, automatic gain control, the AM detector. The series voltage regulator or a power transistor made by BC 108B, 4diada IN 4148, 2k7, 820R, and the 10K trimpot, trimpot functions for selectivity of the controller of all series. Then we using a booster class A and class B amplifier for signal modulated not disappear.

AM Received Schematics

Comments

3 Channels Audio Splitter Amplifier Circuit Diagram using TL084

This is the schematic diagram of 3 channels audio splitter amplifier circuit which built using op-amp IC TL084. The 3 channels amplifier output distribution applies a single TL084. 3 Channels Audio Splitter Amplifier Circuit Diagram The very first step is to capacitive coupling having a p. 1.0 ~ electrolytic capacitor. The entries are railways Vee Y2 or 4.5 V. This enables working with an individual 9V power source. A voltage gain of 10 (1 M?/100 Kohm) is obtained in the first stage, as well as the other three floors are connected as a unity gain voltage followers. Every single output stage drives independently through an amplifier output 50 pF capacitor towards the resistance of 5.1 k ohm load. The response range is flat from 10 Hz to 30 kHz.

A basic Arduino Solar PV Monitor

I have just recently had solar pv installed, mainly to future proof my energy costs, I do not expect it to be like drilling for oil in my back garden, however the return looks to be encouraging. The install gives you another single unit meter, from this you will see the total amount the panels produce, but that is about it. I wanted to know how much the production was as it was happening, I discovered the light blinks on the front of the meter will flash 1000 times for each kWh of electricity which passes through. The rate of the flashing of the LED tells you how much power is currently passing through the meter. [ ]

RF amplifier protection

RF amplifier protection I have developed the protection circuit for the EB104 amplifier I am working on, after I finally had some time to design and test a few models. The main requirements have been: - protection in case of high temperature; - protection in case of high SWR; - protection in case of wrong output filter selection; - simple design (i’m a fan of the whole K.I.S.S. rule of thought), able to work in strong electromagnetic fields, reliable, inexpensive. Because i will be using the same directional coupler i have used in the SWR meter (the one made on PCB) wich is directly influenced by the signal frequency, and because i want full HF coverage, i cannot just measure the reflected signal and make a circuit cut the amplifier when it goes over a limit; on 28Mhz the coupler generates roughly 4 times more voltage that let’s say in 7Mhz. So a system that compares direct and reflected signal and triggers when the latter is percentually too high was needed, therefore an operational a...

TREE

Search This Blog