Skip to main content

Mini Metronome


Linear scale-Small size 40 to 208 beats per minute


Mini Metronome Circuit diagram:
 

Notes:
  • Q1 & Q2 provide linear frequency operation of IC1 following P1 resistance variation.
  • Q3 was added in order to obtain a louder click, similar to clockwork metronomes.
  • 12V micro battery was used to obtain more output power and more compactness.
  • Rotate P1 fully towards R2, then set R1 to obtain 40 beats per minute (compare with another metronome).
  • Rotate P1 fully towards R3, then set R4 to obtain 208 beats per minute.
  • Finally mark the entire scale with the usual metronome steps as following:
  • 40 - 42 - 44 - 46 - 48 - 50 - 52 - 54 - 58 - 60 - 63 - 66 - 69 - 72 - 76 - 80 - 84 - 88 - 92 - 96 - 100 - 104 - 108 - 112 - 116 - 120 - 126 - 132 - 138 - 144 - 152 - 160 - 168 - 176 - 184 - 192 - 200 - 208.

Parts:

P1______100K   Linear Potentiometer
R1_______10K   1/2W Trimmer Cermet
R2_______10K   1/4W Resistor
R3______330K   1/4W Resistor
R4_______50K   1/2W Trimmer Cermet
R5______100K   1/4W Resistor
R6,R7_____1K   1/4W Resistor
C1________1µF   63V Polyester Capacitor
C2_______10nF   63V Polyester Capacitor
C3_______47µF   25V Electrolytic Capacitor
IC1_____NE555   General purpose timer IC
Q1,Q2___BC560   45V 100mA Low noise High gain PNP Transistors
Q3_____ZTX753   100V 2A PNP Transistor
SW1______SPST Switch (Ganged with P1)
SPK______8 Ohm 40mm. Loudspeaker
B1_____12V Battery (MN21, GP23A or VR22 type)

Labels:

Comments

Post a Comment

Popular posts from this blog

3 Channels Audio Splitter Amplifier Circuit Diagram using TL084

This is the schematic diagram of 3 channels audio splitter amplifier circuit which built using op-amp IC TL084. The 3 channels amplifier output distribution applies a single TL084.   3 Channels Audio Splitter Amplifier Circuit Diagram The very first step is to capacitive coupling having a p. 1.0 ~ electrolytic capacitor. The entries are railways Vee Y2 or 4.5 V. This enables working with an individual 9V power source. A voltage gain of 10 (1 M?/100 Kohm) is obtained in the first stage, as well as the other three floors are connected as a unity gain voltage followers. Every single output stage drives independently through an amplifier output 50 pF capacitor towards the resistance of 5.1 k ohm load. The response range is flat from 10 Hz to 30 kHz.
2 comments
Read more

Simple Automatic Street Light

There have been lot of problems in street lights. Major problem in some places is every evening a person has to come and switch ON the street light and it should be again switched off in morning. Yes, this may not be the situation in everywhere but exists in many places. So this problem can be overcome by using a simple circuit. Below shown circuit will be automatically switched ON and OFF during night and morning times respectively. Circuit diagram : Simple Automatic street light Circuit Diagram In above circuit R1 can be used to adjust the sensitivity. And the working of the circuit is very simple. The LDR will have very low resistance during day time so the transistor Q1 will be in OFF condition. And during night time the resistance will be very high so automatically the transistor Q1 will be ON. The Q1 is PNP transistor and the emitter of Q1 is given to base of Q2. So the Q2 transistor will be ON only if the transistor Q1 is ON. The TRIAC is used in the circuit to make is circ...
Post a Comment
Read more

A basic Arduino Solar PV Monitor

I have just recently had solar pv installed, mainly to future proof my energy costs, I do not expect it to be like drilling for oil in my back garden, however the return looks to be encouraging. The install gives you another single unit meter, from this you will see the total amount the panels produce, but that is about it. I wanted to know how much the production was as it was happening, I discovered the light blinks on the front of the meter will flash 1000 times for each kWh of electricity which passes through. The rate of the flashing of the LED tells you how much power is currently passing through the meter. [ ]
Post a Comment
Read more