Skip to main content

HTC exec confirms next generation J Butterfly handset


HTC exec confirms next-generation J Butterfly handset
 
 
HTC Marketing Chief Ben Ho confirmed that the company will be rolling out a successor to the J Butterfly due to high demand, reports Focus Taiwan.

The HTC J Butterfly was launched last year in several Asia territories, to much fan fare. It later saw a US launch labeled as the Droid DNA, which at the time was boasted as one of the top Android handsets on the market. Now, of course, it is outdone by the HTC One that is set for worldwide rollout in the coming weeks.

Ho didn't go into specifics on what the J Butterfly may feature or when it will be released. Given that Verizon isn't slated to carry the HTC One out of the gate, a Droid DNA follow up makes perfect sense, though Ho didn't comment on it. Europe will more than likely be out of the mix for either the J Butterfly or DNA variant.

Last month, Twitter user @LlabTooFeR reported the Droid DNA follow-upwill feature a 1.7GHz Qualcomm APQ8064 processor, 4.7-inch 1080p display, 13-megapixel rear-camera, 2.1-megapixel front-camera, 2GB of RAM, Bluetooth 4, Wi-Fi, SD card support, Android Jelly Bean, and Sense 5. It's worth noting that specs run very close to the HTC One, though UltraPixel tech doesn't seem to be present.

At any rate, folks in Asia who can't wait for their J Butterfly can sleep a little easier knowing that it's on the way, but weep at the loss of UltraPixel tech if rumours are to be believed.
 
 
 
 
Sourced by : MSN

Comments

Popular posts from this blog

3 Channels Audio Splitter Amplifier Circuit Diagram using TL084

This is the schematic diagram of 3 channels audio splitter amplifier circuit which built using op-amp IC TL084. The 3 channels amplifier output distribution applies a single TL084.   3 Channels Audio Splitter Amplifier Circuit Diagram The very first step is to capacitive coupling having a p. 1.0 ~ electrolytic capacitor. The entries are railways Vee Y2 or 4.5 V. This enables working with an individual 9V power source. A voltage gain of 10 (1 M?/100 Kohm) is obtained in the first stage, as well as the other three floors are connected as a unity gain voltage followers. Every single output stage drives independently through an amplifier output 50 pF capacitor towards the resistance of 5.1 k ohm load. The response range is flat from 10 Hz to 30 kHz.

RF amplifier protection

RF amplifier protection I have developed the protection circuit for the EB104 amplifier I am working on, after I finally had some time to design and test a few models. The main requirements have been: - protection in case of high temperature; - protection in case of high SWR; - protection in case of wrong output filter selection; - simple design (i’m a fan of the whole K.I.S.S. rule of thought), able to work in strong electromagnetic fields, reliable, inexpensive. Because i will be using the same directional coupler i have used in the SWR meter (the one made on PCB) wich is directly influenced by the signal frequency, and because i want full HF coverage, i cannot just measure the reflected signal and make a circuit cut the amplifier when it goes over a limit; on 28Mhz the coupler generates roughly 4 times more voltage that let’s say in 7Mhz. So a system that compares direct and reflected signal and triggers when the latter is percentually too high was needed, therefore an operational a...

Simple Automatic Street Light

There have been lot of problems in street lights. Major problem in some places is every evening a person has to come and switch ON the street light and it should be again switched off in morning. Yes, this may not be the situation in everywhere but exists in many places. So this problem can be overcome by using a simple circuit. Below shown circuit will be automatically switched ON and OFF during night and morning times respectively. Circuit diagram : Simple Automatic street light Circuit Diagram In above circuit R1 can be used to adjust the sensitivity. And the working of the circuit is very simple. The LDR will have very low resistance during day time so the transistor Q1 will be in OFF condition. And during night time the resistance will be very high so automatically the transistor Q1 will be ON. The Q1 is PNP transistor and the emitter of Q1 is given to base of Q2. So the Q2 transistor will be ON only if the transistor Q1 is ON. The TRIAC is used in the circuit to make is circ...