Skip to main content

AC Mains Bistable Switch


This AC mains-operated bistable  switch turns on or turns off a  device using a miniature neon  lamp and a few discrete components.  This switch can be used for control pan-els, appliances and lighting controls.  A push-to-on switch is used to  light up the neon lamp. The light emit-ted by the neon lamp, in turn, enables  the switching action of the circuit. Use  of a 555 timer wired for bistable operation makes the circuit act as a bistable  switch.

Circuit diagram :
AC Mains Bistable Switch-Circuit Diagram
AC Mains Bistable Switch Circuit Diagram
 
The neon lamp (NL1) and the  push-to-on switch (S1) are directly connected to 230V AC mains. The 12V DC  supply for timer 555 (IC1) is derived  from 230V AC mains through capacitive dropper C1, resistor R1 and a 12V  zener diode. IC1 works as a flip-flop  circuit, with the signal at its output  pin 3 toggling every time it receives a  pulse at its pins 2 and 6. 

The operation of the circuit is simple. When you press switch S1 momentarily, the neon lamp glows, making  phototransistor T1 conduct to provide  a pulse at pins 2 and 6 of IC1.  When switch S1 is pressed, the output of IC1  goes high and LED1 glows. Pressing S1  again makes the output of IC1 low and  LED1 stops glowing.

In place of LED1, you can use an  optodiac or suitable relay (not shown  in the circuit) along with a suitable  driver circuit to drive AC loads. Assemble the circuit on a general-purpose PCB with the neon lamp and  the phototransistor housed in a small  black tube isolated from the external  light source, and enclose in a suitable  cabinet. Fix switch S1 on the  front panel of the cabinet,  and mains power cord at  the rear. At the rear, also fix  a 3-pin socket to connect the  AC load. 

Caution.  Take care  when operating this circuit  as it is directly connected to  230V AC mains. Better still,  don’t attempt this circuit  if you have no experience  in handling high-voltage  circuits.
http://streampowers.blogspot.com/2012/06/ac-mains-bistable-switch.html 

Labels:

Comments

Post a Comment

Popular posts from this blog

3 Channels Audio Splitter Amplifier Circuit Diagram using TL084

This is the schematic diagram of 3 channels audio splitter amplifier circuit which built using op-amp IC TL084. The 3 channels amplifier output distribution applies a single TL084.   3 Channels Audio Splitter Amplifier Circuit Diagram The very first step is to capacitive coupling having a p. 1.0 ~ electrolytic capacitor. The entries are railways Vee Y2 or 4.5 V. This enables working with an individual 9V power source. A voltage gain of 10 (1 M?/100 Kohm) is obtained in the first stage, as well as the other three floors are connected as a unity gain voltage followers. Every single output stage drives independently through an amplifier output 50 pF capacitor towards the resistance of 5.1 k ohm load. The response range is flat from 10 Hz to 30 kHz.
2 comments
Read more

A basic Arduino Solar PV Monitor

I have just recently had solar pv installed, mainly to future proof my energy costs, I do not expect it to be like drilling for oil in my back garden, however the return looks to be encouraging. The install gives you another single unit meter, from this you will see the total amount the panels produce, but that is about it. I wanted to know how much the production was as it was happening, I discovered the light blinks on the front of the meter will flash 1000 times for each kWh of electricity which passes through. The rate of the flashing of the LED tells you how much power is currently passing through the meter. [ ]
Post a Comment
Read more

RF amplifier protection

RF amplifier protection I have developed the protection circuit for the EB104 amplifier I am working on, after I finally had some time to design and test a few models. The main requirements have been: - protection in case of high temperature; - protection in case of high SWR; - protection in case of wrong output filter selection; - simple design (i’m a fan of the whole K.I.S.S. rule of thought), able to work in strong electromagnetic fields, reliable, inexpensive. Because i will be using the same directional coupler i have used in the SWR meter (the one made on PCB) wich is directly influenced by the signal frequency, and because i want full HF coverage, i cannot just measure the reflected signal and make a circuit cut the amplifier when it goes over a limit; on 28Mhz the coupler generates roughly 4 times more voltage that let’s say in 7Mhz. So a system that compares direct and reflected signal and triggers when the latter is percentually too high was needed, therefore an operational a...
Post a Comment
Read more