Treatment LCD monitor

Treatment LCD Monitor. At this time computer use familiar and already widely used either for work or entertainment. And of course when talking about computers it will not be far away with a device called a monitor. And today use CRT monitors have started to decrease with the LCD Monitor that despite having a price that is quite expensive but have many advantages than conventional CRT monitors.

Here are a few advantages of LCD monitor is a stylish design, flat screen and a brighter color than convex or crt monitor screen, while also LCD Monitors have many advantages among which have a high resolution so that it can help many people especially those working Visual design field.

There are some special treatment for LCD monitors in this case is for the treatment of LCD monitors, the following are some steps steps:

Use the LCD as needed, Do not use if you do not need so-necessary and do not use it 24 hours nonstop jedanya have no time for any electronic item there during his lifetime (Lifetime). Turn off your LCD monitor when your computer dies, in order to save electricity and also keeps your LCD monitor remain durable.

Use the type that has a grounding electrical power, because it can minimize the damage in the event of lightning strikes. This option is optional.

Perform regular cleaning, at least 2 weeks 1 times, for LCD monitors are always in a state clear of dust and other debris. Remember! to clean it must use a very soft cloth that has spread with a special liquid cleaners LCD monitor. If necessary you can buy special equipment to clean the LCD monitor.

Do not engage in cleanup activities in the state of electricity is still flowing, unplug all cables available on the LCD to avoid things that are not desired. The existence of water coming into the series of LCD monitors will be able to cause fatal damage.

Keep the LCD of the things that contain water such as rain water, drinking water etc.. Because all electronic goods electrical short circuit will occur if water enters into the electronic components.

Keep the LCD of goods containing such magnetic sound system, Persani, HP etc. signals. Because it will be fatal is going to happen Noise or damage which may destroy the layout on the monitor screen.

LCD Save a strategic place and safe from the reach of small children, so that you can not avoid tersenggol LCD or a small toy.

Unplug all cables associated with the computer (including LCD) in the event of rain accompanied by lightning, because lightning can be grabbed via the antenna propagate through the cable TV and electricity.

To protect the screen / LCD screen can use the Screen Protector function prevents dust entry into the LCD and also take care of all sorts of scrapes. Remember to choose the screen protector is not a trace when reopened.

If there is damage to your LCD monitors, LCD submit to the experts. Do not disassemble itself without accompanied by experts in the field of electronics. Module Components including LCD monitors that can be easily damaged. LCD Monitor Service you to the service center to ensure the improvement is good and right.

Good article on the LCD monitor is beneficial treatment.

3 Channels Audio Splitter Amplifier Circuit Diagram using TL084

This is the schematic diagram of 3 channels audio splitter amplifier circuit which built using op-amp IC TL084. The 3 channels amplifier output distribution applies a single TL084. 3 Channels Audio Splitter Amplifier Circuit Diagram The very first step is to capacitive coupling having a p. 1.0 ~ electrolytic capacitor. The entries are railways Vee Y2 or 4.5 V. This enables working with an individual 9V power source. A voltage gain of 10 (1 M?/100 Kohm) is obtained in the first stage, as well as the other three floors are connected as a unity gain voltage followers. Every single output stage drives independently through an amplifier output 50 pF capacitor towards the resistance of 5.1 k ohm load. The response range is flat from 10 Hz to 30 kHz.

Simple Automatic Street Light

There have been lot of problems in street lights. Major problem in some places is every evening a person has to come and switch ON the street light and it should be again switched off in morning. Yes, this may not be the situation in everywhere but exists in many places. So this problem can be overcome by using a simple circuit. Below shown circuit will be automatically switched ON and OFF during night and morning times respectively. Circuit diagram : Simple Automatic street light Circuit Diagram In above circuit R1 can be used to adjust the sensitivity. And the working of the circuit is very simple. The LDR will have very low resistance during day time so the transistor Q1 will be in OFF condition. And during night time the resistance will be very high so automatically the transistor Q1 will be ON. The Q1 is PNP transistor and the emitter of Q1 is given to base of Q2. So the Q2 transistor will be ON only if the transistor Q1 is ON. The TRIAC is used in the circuit to make is circ...

A basic Arduino Solar PV Monitor

I have just recently had solar pv installed, mainly to future proof my energy costs, I do not expect it to be like drilling for oil in my back garden, however the return looks to be encouraging. The install gives you another single unit meter, from this you will see the total amount the panels produce, but that is about it. I wanted to know how much the production was as it was happening, I discovered the light blinks on the front of the meter will flash 1000 times for each kWh of electricity which passes through. The rate of the flashing of the LED tells you how much power is currently passing through the meter. [ ]

TREE

Search This Blog