Skip to main content

Kingston HyperX Predator 1TB USB 3 0 Flash Drive


I am quite sure that many of us have attended our fair share of trade shows and conferences over the years that we have amassed quite a collection of USB flash drives in our homes, so much so that these have become not valuable at all compared to the early days when a 32MB USB flash drive was all the rage, and hitting 1GB was like, “Whoa!”. Well, we just love the way that technology progresses over time, and here we are with the Kingston HyperX PREDATOR which offers a whopping 1TB of storage space, and fret not about spending huge amounts of time whenever you transfer data to and from it, as it will feature USB 3.0 connectivity to get the job done as fast as possible.
Kingston HyperX Predator 1TB USB 3.0 Flash Drive

Having the Kingston HyperX PREDATOR around is definitely a boon, especially for those of you who do plenty of traveling and yet need to carry a portable hard drive around. The physical dimension of it is extremely small compared to even the smallest 2.5” portable hard drive around, although the latter has now achieved the 2TB capacity mark. It really depends on what you want to sacrifice – size or price?
Kingston HyperX Predator 1TB USB 3.0 Flash Drive
Basically, the HyperX PREDATOR 1TB USB 3.0 flash drive performed as well as its smaller capacity brethren in most of the tests, but there is one major drawback to it. The thickness happens to make it nigh impossible to use normally just like a standard issue USB flash drive, even more so when you want to hook it up to a USB port that is located at the back of your notebook, and this is where the bundled USB 3.0 extension cable comes in handy. Another major talking point (negative one, unfortunately) would be the humongous price tag, as the 1TB model retails for $1,306.63 on Amazon.com. Imagine the number of portable hard drives you can purchase with that kind of money! [Via]

Comments

Popular posts from this blog

3 Channels Audio Splitter Amplifier Circuit Diagram using TL084

This is the schematic diagram of 3 channels audio splitter amplifier circuit which built using op-amp IC TL084. The 3 channels amplifier output distribution applies a single TL084.   3 Channels Audio Splitter Amplifier Circuit Diagram The very first step is to capacitive coupling having a p. 1.0 ~ electrolytic capacitor. The entries are railways Vee Y2 or 4.5 V. This enables working with an individual 9V power source. A voltage gain of 10 (1 M?/100 Kohm) is obtained in the first stage, as well as the other three floors are connected as a unity gain voltage followers. Every single output stage drives independently through an amplifier output 50 pF capacitor towards the resistance of 5.1 k ohm load. The response range is flat from 10 Hz to 30 kHz.

Simple But Automatic Load Sensing Power Switch

This circuit will automatically switch on several mains-powered "slave" loads when a "master" load is turned on. For example, it will switch on the amplifier and CD player in a stereo system when the receiver is turned on. It works by sensing the current draw of the "master" device through a low value high wattage resistor using a comparator. The output of that comparator then switches on the "slave" relay. The circuit can be built into a power bar, extension cord or power center to provide a convenient set of "smart" outlets that switch on when the master appliance is powered (turn on the computer monitor and the computer, printer and other peripherals come on as well). Automatic Load Sensing Power Switch Circuit Diagram Parts List: Notes: This circuit is designed for 120V operation. For 240V operation, resistors R2 and R6 will need to be changed. A maximum of 5A can be used as the master unless the wattage of R1 is increased S1 provid...

RF amplifier protection

RF amplifier protection I have developed the protection circuit for the EB104 amplifier I am working on, after I finally had some time to design and test a few models. The main requirements have been: - protection in case of high temperature; - protection in case of high SWR; - protection in case of wrong output filter selection; - simple design (i’m a fan of the whole K.I.S.S. rule of thought), able to work in strong electromagnetic fields, reliable, inexpensive. Because i will be using the same directional coupler i have used in the SWR meter (the one made on PCB) wich is directly influenced by the signal frequency, and because i want full HF coverage, i cannot just measure the reflected signal and make a circuit cut the amplifier when it goes over a limit; on 28Mhz the coupler generates roughly 4 times more voltage that let’s say in 7Mhz. So a system that compares direct and reflected signal and triggers when the latter is percentually too high was needed, therefore an operational a...