Simple Soft Start For Switching Power Supply Project

This is a Simple Soft Start For Switching Power Supply Project. Switching power supply whose output voltage is appreciably lower than its input voltage has an interesting property: the current drawn by it is smaller than its output current. However, the input power (UI) is, of course, greater than the output power. There is another aspect that needs to be watched: when the input voltage at switch-on is too low, the regulator will tend to draw the full current. When the supply cannot cope with this, it fails or the fuse blows. It is, therefore, advisable to disable the regulator at switch-on (via the on/off input). until the relevant capacitor has been charged. When the regulator then starts to draw current, the charging current has already dropped to a level which does not overload the voltage source.

Soft Start For Switching Power Supply Circuit diagram:

Soft Start Circuit For Switching Power Supply

The circuit in the diagram provides an output voltage of 5 V and is supplied by a 24 V source. The regulator need not be disabled until the capacitor is fully charged: when the potential across the capacitor has reached a level of half or more of the input voltage, all is well. This is why the zener diode in the diagram is rated at 15 V. Many regulators produced by National Semiconductor have an integral on/off switch, and this is used in the present circuit. The input is intended for TTL signals, and usually consists of a transistor whose base is accessible externally. This means that a higher switching voltage may be applied via a series resistor: the value of this in the present circuit is 22 kΩ. When the voltage across the capacitor reaches a level of about 17 V, transistor T1 comes on, whereupon the regulator is enabled.

Source: National Semiconductors

Comments

Build a 3000W Stereo Power Amplifier Circuit Diagram

How to Build a 3000W Stereo Power Amplifier Circuit Diagram? Lets start first we define 3000wstereo power amplifier circuit diagram this circuit has a power output of up to 1500W RMS power amplifier circuit is often used to power sound systems spelunker for outdor. In the final image can be seen a series of power amplifiers using 10 sets of power transistors for the ending. This power amplifier circuit using a transistor amplifier from the front, signal splitter, driver and power amplifier. Current consumption required is quite large power amplifier that is 15-20 A 1500W power amplifier circuits for this. Supply voltage needed by the power of this amplifier is the optimal working order symmetrical 130VDC (130VDC-130VDC ground). 1500W amplifier circuit below is a picture series of mono, stereo if you want to make it necessary to make two copies of the circuit. For more details can be viewed directly image the following 1500W power amplifier circuit. The series of High Power Amplifier 15

Solid State Switch For Dc Operated Gadgets

This solid state DC switch can be assembled using just three transistors and some passive components. It can be used to switch on one gadget while switching off the second gadget with momentary operation of switch. To reverse the operation, you just have to momentarily depress another switch. The circuit operates over 6V-15V DC supply voltage. It uses positive feedback from transistor T2 to transistor T1 to keep this transistor pair in latched state (on/ off), while the state of the third transistor stage is the complement of transistor T2’s conduction state. Initially when switch S3 is closed, both transistors T1 and T2 are off, as no forward bias is available to these, while the base of transistor T3 is effectively grounded via resistors R8 and R6 (shunted by the load of the first gadget). As a result, transistor T3 is forward biased and gadget 2 gets the supply. This is indicated by glowing of LED2. Circuit diagram : Solid-State Switch For Dc-Operated Gadgets Circuit Diagram Whe

Amplifier Circuit 2 X 10 watt with IC AN7145

This is Stereo Amplifier On this schematic amplifier circuit use the ic AN7145L , but can use the following IC : AN7145M AN7145H AN7146M AN7146H You can use of all ic above. anthis circuit need suply voltage with dual voltage . Minimum voltage 6 Volt and maximum voltage 20 volt . Voltage just (-) and (+), but (-) can also ground. Maximum power output 2 X 20 watt with minimum impedance 4 ohm. Click image to view enlarge. You can operate this circuit with plugging input to , PC or other media can give signal audio.

TREE

Search This Blog