Skip to main content

Simple LM3410 LED Driver


The LM3410 IC is a constant current LED driver useful in either boost con-verter or SEPIC design applications. A SEPIC (Single Ended Primary Induct-ance Conver ter) design allows the power supply’s output voltage to be set above, below or equal to its input voltage. In this application the chip is configured as a boost-converter (i.e. the output voltage is greater than the input voltage). 

LM3410 LED Driver Circuit Diagram

Simple LM3410 LED Driver
The LM3410 is available in two fixed-frequency variants. Using either the 525 kHz or 1.6 MHz clock version it is possi-ble to build a ver y compact LED driver. The output stage can supply up to 2.8 A, allowing several high-power LEDs to be driven from a rechargeable Lithium cell or several 1.5 V bat-teries. The chip also features a dimmer input giving simple PWM brightness control.Output current is defined by an external shunt resistor. To keep losses low the LM3410 uses an internal voltage reference of just 190 mV.
Power dissipation in the shunt resistor is therefore low. Using the desired value of LED current the value and power dissipation of the shunt resistor is given by:

R_Shunt = 0.19 V/I_LED
P_Shunt = 0.19 V*I_LED 

A 10 µH coil (L1) will be suf ficient for most applications providing it has a suitable satu-ration current rating. The Input and output capacitors should be 10 µF ceramic t ypes with a low value of E SR . Many distributor s including Farnell stock these component s. The Diode should beaSchottky type (as in all switching regulators). The author has developed a PCB for this design; the corresponding Eagle files can be freely downloaded from www.elektor.com/090850. In sum-mar y the most important features of the LM3410 are:
  • Integrated 2.8 A MOSFET driver.
  • Input voltage range from 2.7 V to 5.5 V.
  • Capability to drive up to six series connected LEDs (maximum output 24 V).
  • Up to 88 % efficiency.
  • Available is 525 kHz and 1.6 MHz versions.
  • Allows both boost and SEPIC designs.
  • Available in 5 pin SOT23 or 6 pin LLP outline.

Labels:

Comments

Post a Comment

Popular posts from this blog

3 Channels Audio Splitter Amplifier Circuit Diagram using TL084

This is the schematic diagram of 3 channels audio splitter amplifier circuit which built using op-amp IC TL084. The 3 channels amplifier output distribution applies a single TL084.   3 Channels Audio Splitter Amplifier Circuit Diagram The very first step is to capacitive coupling having a p. 1.0 ~ electrolytic capacitor. The entries are railways Vee Y2 or 4.5 V. This enables working with an individual 9V power source. A voltage gain of 10 (1 M?/100 Kohm) is obtained in the first stage, as well as the other three floors are connected as a unity gain voltage followers. Every single output stage drives independently through an amplifier output 50 pF capacitor towards the resistance of 5.1 k ohm load. The response range is flat from 10 Hz to 30 kHz.
2 comments
Read more

Simple But Automatic Load Sensing Power Switch

This circuit will automatically switch on several mains-powered "slave" loads when a "master" load is turned on. For example, it will switch on the amplifier and CD player in a stereo system when the receiver is turned on. It works by sensing the current draw of the "master" device through a low value high wattage resistor using a comparator. The output of that comparator then switches on the "slave" relay. The circuit can be built into a power bar, extension cord or power center to provide a convenient set of "smart" outlets that switch on when the master appliance is powered (turn on the computer monitor and the computer, printer and other peripherals come on as well). Automatic Load Sensing Power Switch Circuit Diagram Parts List: Notes: This circuit is designed for 120V operation. For 240V operation, resistors R2 and R6 will need to be changed. A maximum of 5A can be used as the master unless the wattage of R1 is increased S1 provid...
Post a Comment
Read more

RF amplifier protection

RF amplifier protection I have developed the protection circuit for the EB104 amplifier I am working on, after I finally had some time to design and test a few models. The main requirements have been: - protection in case of high temperature; - protection in case of high SWR; - protection in case of wrong output filter selection; - simple design (i’m a fan of the whole K.I.S.S. rule of thought), able to work in strong electromagnetic fields, reliable, inexpensive. Because i will be using the same directional coupler i have used in the SWR meter (the one made on PCB) wich is directly influenced by the signal frequency, and because i want full HF coverage, i cannot just measure the reflected signal and make a circuit cut the amplifier when it goes over a limit; on 28Mhz the coupler generates roughly 4 times more voltage that let’s say in 7Mhz. So a system that compares direct and reflected signal and triggers when the latter is percentually too high was needed, therefore an operational a...
Post a Comment
Read more