Skip to main content

NES Controller


The article will guide you on how to use NES controller in Atari 2600 or ZX Spectrum using an Arduino. Read through the entire article to have a better idea. An arduino and a few connectors are the only components involved here. Since the source code is small, any Arduino board can be utilized. The detailed list of components involved is mentioned below:
  • Arduino
  • DB-9 Male connectors – 2 nos
  • DB-9 Female connector
  • 5 Leds for the test dongle
  • 5 resistors 330 Ohms 1/4 Watt for the test dongle
  • Connecting wires
Hacks and Mods: DIY NES Controller

The DB-9 female plus wires can be replaced by a used Atari Joystick cable if required. The NES cable also can be cut and connected to the arduino. But the wires should be identified without any confusion. The source code is compiled and uploaded to the Ardunio. IDE version 0.22 was used to develop the code. In order to observe the exact behavior of the circuit, a dongle has to be used before the circuit is conneced to the ATARI. Buttons on the NES controller are used to activate the LEDs in the dongle.

The Arduino board has to be powered if a dongle is used for testing the circuit. The joystick controller provides the necessary power that is required for the Arduino to function. No external power is required in this case. This marks the end of the design and testing. The controller is now complete and ready for use.
 

Labels:

Comments

Post a Comment

Popular posts from this blog

3 Channels Audio Splitter Amplifier Circuit Diagram using TL084

This is the schematic diagram of 3 channels audio splitter amplifier circuit which built using op-amp IC TL084. The 3 channels amplifier output distribution applies a single TL084.   3 Channels Audio Splitter Amplifier Circuit Diagram The very first step is to capacitive coupling having a p. 1.0 ~ electrolytic capacitor. The entries are railways Vee Y2 or 4.5 V. This enables working with an individual 9V power source. A voltage gain of 10 (1 M?/100 Kohm) is obtained in the first stage, as well as the other three floors are connected as a unity gain voltage followers. Every single output stage drives independently through an amplifier output 50 pF capacitor towards the resistance of 5.1 k ohm load. The response range is flat from 10 Hz to 30 kHz.
2 comments
Read more

A basic Arduino Solar PV Monitor

I have just recently had solar pv installed, mainly to future proof my energy costs, I do not expect it to be like drilling for oil in my back garden, however the return looks to be encouraging. The install gives you another single unit meter, from this you will see the total amount the panels produce, but that is about it. I wanted to know how much the production was as it was happening, I discovered the light blinks on the front of the meter will flash 1000 times for each kWh of electricity which passes through. The rate of the flashing of the LED tells you how much power is currently passing through the meter. [ ]
Post a Comment
Read more

RF amplifier protection

RF amplifier protection I have developed the protection circuit for the EB104 amplifier I am working on, after I finally had some time to design and test a few models. The main requirements have been: - protection in case of high temperature; - protection in case of high SWR; - protection in case of wrong output filter selection; - simple design (i’m a fan of the whole K.I.S.S. rule of thought), able to work in strong electromagnetic fields, reliable, inexpensive. Because i will be using the same directional coupler i have used in the SWR meter (the one made on PCB) wich is directly influenced by the signal frequency, and because i want full HF coverage, i cannot just measure the reflected signal and make a circuit cut the amplifier when it goes over a limit; on 28Mhz the coupler generates roughly 4 times more voltage that let’s say in 7Mhz. So a system that compares direct and reflected signal and triggers when the latter is percentually too high was needed, therefore an operational a...
Post a Comment
Read more