Skip to main content

Make Your Iphone Battery Last Longer


I’ve owned a Iphone for a while now, it’s an amazing phone, the best I have ever used so far. But when I first started using it, my only concern was that the battery didn’t last as much as I expected. After two days, it was gone, and when I needed it, the phone just didn’t turn ON. I used to let the wireless on almost all the time and downloading many new apps. Now that I have some more experience on how my little gadget works, I will try to share some ideas on how you can optimize your iphone’s battery life and have a better iExperience.

iphone


  • Wireless connectivity will drawn your battery even if you are not using it. Keeping it on, it will always try to connect to some open hot spot, try to check your emails and much more. So a good idea is to turn it on when using, and after, turn it off.
  • Bluetooth have a similar battery usage as Wi-Fi, so there’s not much reason to leave it on if you are not using it (I believe that the most common usage for bluetooth today is the headsets and car kits).
  • Auto-Brightness is a interesting thing apple made to make the battery last longer. It uses iphone’s camera to adjust brightness based on the lighting conditions outside, so it will automatically set, for example, to make it less bright when you are on a dark place. Great feature!
  • Music EQ will have a significant battery usage if you listen to your songs for many hours everyday, as it uses more processing power. So if you want to charge less your iphone, it is another thing you may consider turning it off.
  • Heat can be a problem to your iphone, as it is a very bad thing to lithium-ion batteries, making them harder to charge and destroying it due the intense ionization. So remember to never let your phone in a hot place such as inside a car or in direct sunlight. If you are using some kind of carrying case, you need to be even more careful about this, and remember to take it off when charging your mobile, as it gets warm when charging.
  • Keep it charging! After putting your phone to charge, leave it there for some hours more after it says it’s full. It will make your phone battery last much more, you will be surprised! After done that, my iphone battery lasted more then a week, way more if you compare to the 2-3 days when I was disconnecting if from the dock just after it says its full.
  • Background Programs! This is important, new iphones, such as Iphone4 allows you to run multiple apps on the background, but this will drain your battery fast if you forget to close them. To do this, double click on the round button and it will show all the apps currently running, keep clicking in one of the apps and a red “X” will apear, then you can close all apps.
    • What else do you do to make your iphone battery last longer?




    Source by : link

    Labels:

    Comments

    Post a Comment

    Popular posts from this blog

    3 Channels Audio Splitter Amplifier Circuit Diagram using TL084

    This is the schematic diagram of 3 channels audio splitter amplifier circuit which built using op-amp IC TL084. The 3 channels amplifier output distribution applies a single TL084.   3 Channels Audio Splitter Amplifier Circuit Diagram The very first step is to capacitive coupling having a p. 1.0 ~ electrolytic capacitor. The entries are railways Vee Y2 or 4.5 V. This enables working with an individual 9V power source. A voltage gain of 10 (1 M?/100 Kohm) is obtained in the first stage, as well as the other three floors are connected as a unity gain voltage followers. Every single output stage drives independently through an amplifier output 50 pF capacitor towards the resistance of 5.1 k ohm load. The response range is flat from 10 Hz to 30 kHz.
    2 comments
    Read more

    Simple But Automatic Load Sensing Power Switch

    This circuit will automatically switch on several mains-powered "slave" loads when a "master" load is turned on. For example, it will switch on the amplifier and CD player in a stereo system when the receiver is turned on. It works by sensing the current draw of the "master" device through a low value high wattage resistor using a comparator. The output of that comparator then switches on the "slave" relay. The circuit can be built into a power bar, extension cord or power center to provide a convenient set of "smart" outlets that switch on when the master appliance is powered (turn on the computer monitor and the computer, printer and other peripherals come on as well). Automatic Load Sensing Power Switch Circuit Diagram Parts List: Notes: This circuit is designed for 120V operation. For 240V operation, resistors R2 and R6 will need to be changed. A maximum of 5A can be used as the master unless the wattage of R1 is increased S1 provid...
    Post a Comment
    Read more

    RF amplifier protection

    RF amplifier protection I have developed the protection circuit for the EB104 amplifier I am working on, after I finally had some time to design and test a few models. The main requirements have been: - protection in case of high temperature; - protection in case of high SWR; - protection in case of wrong output filter selection; - simple design (i’m a fan of the whole K.I.S.S. rule of thought), able to work in strong electromagnetic fields, reliable, inexpensive. Because i will be using the same directional coupler i have used in the SWR meter (the one made on PCB) wich is directly influenced by the signal frequency, and because i want full HF coverage, i cannot just measure the reflected signal and make a circuit cut the amplifier when it goes over a limit; on 28Mhz the coupler generates roughly 4 times more voltage that let’s say in 7Mhz. So a system that compares direct and reflected signal and triggers when the latter is percentually too high was needed, therefore an operational a...
    Post a Comment
    Read more