Lighting Up Model Aircraft

This circuit provides aircraft modellers with extremely realistic beacon and marker lights at minimum outlay. The project ’s Strobe out-put (A) provides four brief pulses repeated periodically for the wing (white strobe) lights. In addition the Beacon output (B) gives a double pulse to drive a red LED for indicating the aircraft’s active operational status. On the proto-type this is usually a red rotating beacon known as an Anti-Collision Light (ACL). The circuit is equally useful for road vehicle modellers, who can use it to flash headlights and blue emergency lights.

Lighting Up Model Aircraft Circuit diagram :

Lighting Up Model Aircraft Circuit Diagram

All signals are generated by a 4060 14-stage binary counter and some minimal output selection logic. Cycle time is determined by the way the internal oscillator is con-figured (resistor and capacitor on pins 9/10) and can be varied within quite broad limits. High-efficiency LEDs are your first choice for the indicators connected to the Bea-con and Strobe outputs (remember to fit series resistors appropriate to the operating voltage Ub and the current specified for the LED used).

The sample circuit is for operating voltages between 5 and 12 V. Cur- rent flow through the two BS170 FET devices must not exceed 500 mA.

Author : Werner Ludwig

Comments

3 Channels Audio Splitter Amplifier Circuit Diagram using TL084

This is the schematic diagram of 3 channels audio splitter amplifier circuit which built using op-amp IC TL084. The 3 channels amplifier output distribution applies a single TL084. 3 Channels Audio Splitter Amplifier Circuit Diagram The very first step is to capacitive coupling having a p. 1.0 ~ electrolytic capacitor. The entries are railways Vee Y2 or 4.5 V. This enables working with an individual 9V power source. A voltage gain of 10 (1 M?/100 Kohm) is obtained in the first stage, as well as the other three floors are connected as a unity gain voltage followers. Every single output stage drives independently through an amplifier output 50 pF capacitor towards the resistance of 5.1 k ohm load. The response range is flat from 10 Hz to 30 kHz.

Apples Next iPhone to Arrive Sept 10

Apple will unveil the next edition of the iPhone at a major press event on Sept. 10, according to All Things D.Other than the purported date for the unveiling of the so-called iPhone 6, the site's Ina Fried did not offer any details about what else we might expect from Apple with the arrival of the company's first new smartphone since the debut of the iPhone 5 last September. If Apple does lift the curtain on its next-generation iPhone on Sept. 10, it would be two days short of a full year since the iPhone 5 was revealed. While Apple CEO Tim Cook is rumored to be under pressure from Apple's board to step up the pace of innovation and product release schedules, that lag between new iPhone releases wouldn't be particularly unusual for the company—Apple went 16 months between introducing the iPhone 4 and iPhone 4S , for example. But as Fried noted, even as Apple has continued to enjoy robust sales of the iPhone this year, the company has seen its overall share of the gl...

RF amplifier protection

RF amplifier protection I have developed the protection circuit for the EB104 amplifier I am working on, after I finally had some time to design and test a few models. The main requirements have been: - protection in case of high temperature; - protection in case of high SWR; - protection in case of wrong output filter selection; - simple design (i’m a fan of the whole K.I.S.S. rule of thought), able to work in strong electromagnetic fields, reliable, inexpensive. Because i will be using the same directional coupler i have used in the SWR meter (the one made on PCB) wich is directly influenced by the signal frequency, and because i want full HF coverage, i cannot just measure the reflected signal and make a circuit cut the amplifier when it goes over a limit; on 28Mhz the coupler generates roughly 4 times more voltage that let’s say in 7Mhz. So a system that compares direct and reflected signal and triggers when the latter is percentually too high was needed, therefore an operational a...

TREE

Search This Blog