Skip to main content

Final Nikon Coolpix S800c Runs on Android 2 3 Gingerbread



Normally, when we talk about an Android-powered system, we would venture into the realm of smartphones and tablets, and very rarely (if ever) into the world of digital cameras. The line is about to be blurred this day, as the Nikon Coolpix S800c was just announced to come with a copy of the Android operating system – Android 2.3 Gingerbread, to be exact. Yes sir, how does this digital camera shape up in the face of a mobile operating system running in the background? Well, we shall have to take a closer look at its machinations and inner workings right after the jump, shall we not ?

For starters, with Android running on the Nikon Coolpix S800c, you might actually feel that you are using a smartphone at times – until you realize that you are unable to make any phone calls or receive text messages. Good thing it has Wi-Fi connectivity built in though, as it would not be much of an Android device if there were not Internet connectivity to make it interactive.

Setting up the camera for Internet connection using operations which are similar to those used by Android smartphones is possible, not to mention easy. You are also able to post whatever you have snapped and recorded onto social networking sites like Google+, Facebook, and Twitter in a jiffy, but make sure you are within the vicinity of a Wi-Fi network, otherwise it would all amount to nought.

Not only that, the Nikon Coolpix S800c has a new feature known as “Upload to Smart Device”, where this app can be used to transfer high-resolution photos and movies to smart devices which are powered by the Android or iOS operating system, again, over a wireless connection. As for the performance of the Nikon Coolpix S800c, what kind of camera specifications does it pack?

We do know it will come equipped with a 10x optical zoom NIKKOR lens, in addition to a built-in lens-shift vibration reduction (VR) function. There is also a backside illumination CMOS sensor that boasts of an effective pixel count of 16-megapixels so that you can shoot images with little noise at the high sensitivities – perfect for low light conditions or night landscapes.

You are also able to record 1920 x 1080p/30-fps full-HD movies with stereo sound, and the included high-performance GPS module is able to record your current position (latitude and longitude) information, applying them to photos and movies as they are recorded. 

Comments

Popular posts from this blog

3 Channels Audio Splitter Amplifier Circuit Diagram using TL084

This is the schematic diagram of 3 channels audio splitter amplifier circuit which built using op-amp IC TL084. The 3 channels amplifier output distribution applies a single TL084.   3 Channels Audio Splitter Amplifier Circuit Diagram The very first step is to capacitive coupling having a p. 1.0 ~ electrolytic capacitor. The entries are railways Vee Y2 or 4.5 V. This enables working with an individual 9V power source. A voltage gain of 10 (1 M?/100 Kohm) is obtained in the first stage, as well as the other three floors are connected as a unity gain voltage followers. Every single output stage drives independently through an amplifier output 50 pF capacitor towards the resistance of 5.1 k ohm load. The response range is flat from 10 Hz to 30 kHz.

Simple Automatic Street Light

There have been lot of problems in street lights. Major problem in some places is every evening a person has to come and switch ON the street light and it should be again switched off in morning. Yes, this may not be the situation in everywhere but exists in many places. So this problem can be overcome by using a simple circuit. Below shown circuit will be automatically switched ON and OFF during night and morning times respectively. Circuit diagram : Simple Automatic street light Circuit Diagram In above circuit R1 can be used to adjust the sensitivity. And the working of the circuit is very simple. The LDR will have very low resistance during day time so the transistor Q1 will be in OFF condition. And during night time the resistance will be very high so automatically the transistor Q1 will be ON. The Q1 is PNP transistor and the emitter of Q1 is given to base of Q2. So the Q2 transistor will be ON only if the transistor Q1 is ON. The TRIAC is used in the circuit to make is circ...

A basic Arduino Solar PV Monitor

I have just recently had solar pv installed, mainly to future proof my energy costs, I do not expect it to be like drilling for oil in my back garden, however the return looks to be encouraging. The install gives you another single unit meter, from this you will see the total amount the panels produce, but that is about it. I wanted to know how much the production was as it was happening, I discovered the light blinks on the front of the meter will flash 1000 times for each kWh of electricity which passes through. The rate of the flashing of the LED tells you how much power is currently passing through the meter. [ ]