Skip to main content

50W DC DC Converters TRACOPOWER with the Highest Power Density


TRACOPOWER launches the high performance TEN50 Series with 12 models providing 50W power in a 1”x 2”x 0.4 “ compact package. Today already almost all of applications require a high efficiency of a voltage conversion. When we add to this requirement also saving of space and a galvanic isolation, we´ll get to widely used components – DC/DC modules. The TEN 50 Series models feature a very high efficiency of up to 92%. Excellent efficiency is maintained in over a wide load range and no minimum load is required for an accurate output regulation. They are available in three basic groups – TEN 50-12xx, TEN 50-24xx a TEN 50-48xx with a wide input voltage range (2:1).

50W DC/DC Converters TRACOPOWER with the Highest Power Density
 
Low thermal losses and the use of highest grade components allow an operating temperature range of –40°C to +85°C while up to 55°C no forced air cooling is required. With an optional heat-sink this temperature can even be increased. An operation without a forced air cooling is possible even at higher temperatures – at an adequate power derating ( 2%/K above 55°C and 2,5%/K above 65°C). The TEN 50 Series comes with remote On/Off function and have an adjustable output voltage (± 10%). Protection against overload and short-circuit, very compact dimensions and a 1500VDC isolation enable usage of TEN 50 modules in virtually any power application. [ ]

Comments

Popular posts from this blog

A basic Arduino Solar PV Monitor

I have just recently had solar pv installed, mainly to future proof my energy costs, I do not expect it to be like drilling for oil in my back garden, however the return looks to be encouraging. The install gives you another single unit meter, from this you will see the total amount the panels produce, but that is about it. I wanted to know how much the production was as it was happening, I discovered the light blinks on the front of the meter will flash 1000 times for each kWh of electricity which passes through. The rate of the flashing of the LED tells you how much power is currently passing through the meter. [ ]

Build a Key Operated Gate Locking System Circuit

This simple key-operated gate locking system allows only those persons who know the preset code to open the gate. The code is to be entered from the keypad within the preset time to operate the motor fitted in the gate. If anyone trying to open the gate presses a wrong key in the keypad, the system is disabled and, at the same time, sounds an alarm to alert you of an unauthorized entry. Figs 1 and 2 show the block and circuit diagrams of the key-operated code locking system, respectively. Connect points A, B, C, D, E, F and ground of the circuit to the respective points of the keypad. Keys S7, S16, S14 and S3 are used here for code entry, and the remaining keys are used for disabling the system. It is very important to press the keys in that order to form the code. To start the motor of the gate, press switches S7, S16, S14 and S3 sequentially. If the keys are pressed in a different order from the preset order, the system will lock automatically and the motor will not start. Fig. 1: Bl...

Simple But Automatic Load Sensing Power Switch

This circuit will automatically switch on several mains-powered "slave" loads when a "master" load is turned on. For example, it will switch on the amplifier and CD player in a stereo system when the receiver is turned on. It works by sensing the current draw of the "master" device through a low value high wattage resistor using a comparator. The output of that comparator then switches on the "slave" relay. The circuit can be built into a power bar, extension cord or power center to provide a convenient set of "smart" outlets that switch on when the master appliance is powered (turn on the computer monitor and the computer, printer and other peripherals come on as well). Automatic Load Sensing Power Switch Circuit Diagram Parts List: Notes: This circuit is designed for 120V operation. For 240V operation, resistors R2 and R6 will need to be changed. A maximum of 5A can be used as the master unless the wattage of R1 is increased S1 provid...